Pioneer VSA-AX10Ai-S - Manual (Page 79)

Other connections 09
79
En
1 Use an i.LINK cable to connect one of the i.LINK
connectors on this amplifier to an i.LINK connector
on your i.LINK component.
• The arrow on the cable connector body should be
face down and lined up with the arrow below the
connector on the amplifier for correct alignment. The
i.LINK cable should be inserted straight into the
connector so that it snaps easily into place. If not
connected properly the amplifier will not be able to
recognize any connected components. Note that the
i.LINK cable is fragile and can be broken easily if too
much force is used when connecting.
2 Assign the i.LINK component to the input you
want, then make any necessary output settings on
the component.
See
Assigning the i.LINK inputs on page 84 to assign the
component to an input on this amplifier. Follow the
operating instructions that came with the component to
make any necessary output settings.
Note
• You can connect several components together using
i.LINK. See Creating an i.LINK network below.
About i.LINK
i.LINK is a trademark name for IEEE1394, a high-speed
interface for digital audio, video and other data found on
personal computers, digital camcorders, and other kinds
of audio and audio/visual equipment. A single i.LINK
connector can both send and receive data at the same
time, so only one cable is required to connect compo-
nents for two-way communication.
“i.LINK” and the “i.LINK” logo are trademarks of Sony
Corporation.
About PQLS rate control
Pioneer's PQLS (Precision Quartz Lock System)
technology provides high-precision digital audio from
DVD-A, SACD and audio CD sources when you use the
i.LINK interface. A precision quartz controller in this
amplifier eliminates distortion caused by timing errors
(jitter), giving you the best possible digital-to-analog
conversion from the digital source.
To take advantage of PQLS, you must have a player
compatible with rate-control, and it must be switched on
and connected to this amplifier through the i.LINK
network.
Creating an i.LINK network
Using i.LINK it is possible to chain up to 17 components
together so that the digital audio and control signals
from each component is available to other components
in the network. With the addition of an i.LINK repeater,
it’s possible to connect up to 63 components.
i.LINK connectors come in 4-pin and 6-pin configura-
tions. This player uses the 4-pin connection, but the two
types can be mixed on a network.
This amplifier is compatible with i.LINK Audio (A&M
protocol) components, such as DVD players. Note that
when connected to i.LINK MPEG-II TS equipment (such
as a digital satellite tuner), i.LINK DV equipment (such as
a DVD recorder or DV camcorder), or an i.LINK-equipped
personal computer, audio and video signals are not
transmitted, and connecting to these devices sometimes
causes network interruptions. Check the operating
instructions supplied with your other i.LINK components
for compatibility information.
This amplifier is DTCP (Digital Transmission Content
Protection) compliant, so you can play DVD-A, DVD-
Video, and SACD i.LINK audio.
AUDIO POWER
AMP
IN
PRE OUT
AUDIO
PHONO
FRONT SUB W CENTER
SUR- ROUND BACK
SUR- ROUND
SUB W.
CENTER
SUR- ROUND
CD-R/
TAPE1/ MD
TAPE 2 MONITOR
IN
VIDEO AUDIO S2 VIDEO
USB AUDIO
S400 (AUDIO)
OUT 2
OUT 1
(CD-R/ TAPE1/
MD)
(DVR/
VCR1)
(SAT)
IN
(CD)
(TV/
DVD)
(DVD/
LD)
(DVD/
LD)
IN
DVR/
VCR1
OUT
DVD/
LD IN
(DVD/ LD)
IN
Y
P B
P R
P B
P R
2 RF
IN
IN IN
CD
IN
TUNER
IN
PLAY
IN
PLAY
IN
Y
P B
P R
Y
P B
P R
Y
TV/
DVD IN
SAT IN
IN
IN
IN
IN
OUT
OUT
OUT
12V TRIGGER
IN
IN
IN
VCR2
OUT
IN
VCR3
OUT
IN
1 IN
OUT REC
OUT REC
DIGITAL MONITOR OUT 1
MONITOR
OUT 2
MONITOR OUT
COMPONENT VIDEO
ASSIGNABLE MULTI CH INPUT RS-232C
2 IN
3 IN
4
IN
5
R L
R L
R L (Single)
1
(Single)
2
(Single)
R L
R L
R L
R L
R L
IN
6
ASSIGNABLE
CONTROL
3
1
2
OUT IN
(AUDIO)
S400
i.LINK-equipped component