Pioneer SC-LX73 - Manual (Page 80)

Controlling the rest of your system (In case of SC-LX83) 10
80
En
Operating multiple receivers
The remote control included with this receiver can be
used to operate up to three other receivers (of the same
model as this receiver) in addition to this receiver.
1
The
receiver to be operated is switched by inputting the
preset code to set the remote control setting.
• Set the remote modes on the receivers before using
this function (see Remote Control Mode Setup on
page 115).
1 Check that the remote control’s MULTI-ZONE
selector switch is set to MAIN and that the operation
selector switch is set to RECEIVER.
2 While pressing MULTI OPERATION, press HOME
MENU.
The remote display shows
SETUP MENU.
3 Use
/ to select ‘CHANGE RC MODE’, then press
ENTER.
4 Use
/ to select the remote mode.
RC MODE 1 to 4 can be selected.
5 Press ENTER to set the remote mode.
The selected mode flashes for 3 seconds.
To operate another receiver, start over from step 1 to
input its preset code.
Setting the remote to control other
components
Most components can be assigned to one of the input
function buttons (such as
DVD or CD) using the component’s
manufacturer preset code stored in the remote.
However, there are cases where only certain functions
may be controllable after assigning the proper preset
code, or the codes for the manufacturer in the remote
control will not work for the model that you are using.
If you can’t find a preset code that matches the
component you want to control, you can still teach the
remote individual commands from another remote
control (see Programming signals from other remote
controls on page 81).
• For greater convenience, assign the TV connected to
the MONITOR OUT terminal to the TV operation
selector switch, and assign your satellite/cable receiver
or set-top box connected to the TV input terminal to the
TV input button. If a single device is connected to both
terminals, that device should be assigned to both the
TV operation selector switch and TV input buttons.
• Devices may be assigned to the following input
function buttons.
Selecting preset codes directly
1 While pressing MULTI OPERATION, press HOME
MENU.
The remote display shows
SETUP MENU.
2 Use
/ to select ‘PRESET RECALL’, then press
ENTER.
3 Press the input function button for the component
you want to control, then press ENTER.
When assigning preset codes to
TV CONTROL, set the
remote control operation selector switch to TV here.
The remote display shows the component you want to
control (for example DVD or TV).
2
4 Use
/ to select the first letter of the brand name
of your component, then press ENTER.
This should be the manufacturer’s name (for example,
P
for Pioneer).
5 Use
/ to select the manufacturer’s name from
the list, then press ENTER.
6 Use
/ to select the proper code from the list,
then try using this remote with your component.
The code should start with the component type (for
example,
DVD 020). If there is more than one, start with
the first one.
3
To try out the remote control, switch the component on or
off (into standby) by pressing
 SOURCE. If it doesn’t seem
to work, select the next code from the list (if there is one).
• If you can’t find or properly enter a preset code, you
can still teach the remote individual commands from
another remote control (see Programming signals
from other remote controls on page 81).
7 If your component is controlled successfully, press
ENTER to confirm.
The remote display shows
OK.
Note
1 This function is only valid when RECEIVER is set to IR MODE at the remote control’s IR/RF SELECT setting (page 88).
2 You can’t assign TUNER, HMG NET RADIO, ADAPTER and iPod USB.
3 • When using a Pioneer HDD recorder, please select PIONEER DVR 450, 451 or 452.
• When using a Pioneer flat panel TV released prior to summer 2005, please select preset code 644.
RECEIVER SOURCE MAIN
MULTI
OPERATION
ZONE2 3
INPUT SELECT
PHONO VIDEO CD-R IN
AUX
DVD
iPod
USB OPTION
MULTI CH
ADAPTER
NET RADIO
CD
TUNER
HMG
BD
TV
HDMI DVR
BDR
1 2
MULTI
OPERATION