Pioneer SC-LX85 - Manual (Page 64)

Setting What it does
OPERATION
MODE
The remote control unit’s operation
screen switches automatically when
the receiver’s input is switched (This is
only valid when the operation selector
switch is set to SOURCE). See Setting
the remote control operation mode on
page 72.
KEY RESET
This is a function for resetting preset
codes that have been set. Key reset-
ting can be done for individual input
functions. See Resetting the input
assignment of one of the input function
buttons on page 66.
ALL RESET
This is a function for resetting all
remote control unit settings you have
made to the defaults set upon ship-
ment from the factory. See Resetting
the remote control settings on page 66.
READ
PRESET ID
The preset codes set for the different
input functions can be checked. See
Confirming preset codes on page 66.
CHANGE
RC MODE
If you have multiple Pioneer receivers,
amplifiers, etc., this setting can be
used to prevent other units from oper-
ating simultaneously when the remote
control unit is operated. See Operating
multiple receivers on page 64.
EXIT
SETUP
Exits the setup menu.
Note
! You can cancel or exit any of the steps by press
and hold MULTI OPERATION for a couple of
seconds. To go back a step, press RETURN.
! After one minute of inactivity, the remote
automatically exits the operation.
Operating multiple receivers
The remote control included with this receiver
can be used to operate up to three other receiv-
ers (of the same model as this receiver) in addi-
tion to this receiver. The receiver to be operated
is switched by inputting the preset code to set
the remote control setting.
! This function is only valid when RECEIVER
is set to IR MODE at the remote control’s
IR/RF SELECT setting (page 71).
! Set the remote modes on the receivers before
using this function (see Remote Control Mode
Setup on page 92).
1 Check that the remote control’s
MULTI-ZONE selector switch is set to MAIN
and that the operation selector switch is
set to RECEIVER.
2 While pressing MULTI OPERATION,
press HOME MENU.
The remote display shows SETUP MENU.
3 Use i/j to select ‘CHANGE RC MODE’,
then press ENTER.
4 Use
i/j to select the remote mode.
RC MODE 1 to 4 can be selected.
5 Press ENTER to set the remote mode.
The selected mode flashes for 3 seconds.
To operate another receiver, start over from step
1 to input its preset code.
Setting the remote to control
other components
Most components can be assigned to one of
the input function buttons (such as DVD or CD)
using the component’s manufacturer preset
code stored in the remote.
However, there are cases where only certain
functions may be controllable after assigning
the proper preset code, or the codes for the
manufacturer in the remote control will not
work for the model that you are using.
If you can’t find a preset code that matches the
component you want to control, you can still
teach the remote individual commands from
another remote control (see Programming sig-
nals from other remote controls on page 65).
En 64
10 Controlling the rest of your system (In case of SC-LX85)
Controlling the rest of your system
(In case of SC-LX85)
About the Remote Setup menu
Important
! This section includes explanations for the SC-
LX85’s remote control. For instructions for the
SC-LX75’s remote control, see Controlling the
rest of your system (In case of SC-LX75) on page
74.
The Remote Setup mode is set by pressing
the HOME MENU button while pressing
MULTI OPERATION. The different items on the
Remote Setup menu are described below. For
their setting procedures, refer to the explana-
tions for the respective items.
Setting What it does
PRESET
RECALL
Preset codes can be set for the various
input functions. The remote control
codes of a number of other devices
(including products of other brands)
are preset in the remote control to
allow these devices to be operated.
See Selecting preset codes directly on
page 65.
CODE
LEARNING
If the desired operations cannot be
performed even though you have set
the preset codes, the remote control
signals of other devices can be learned
directly. See Programming signals from
other remote controls on page 65.
MULTI
OPERATE
A series of the remote control opera-
tions for starting listening or viewing
can be programmed. Multiple remote
control codes can be set for the differ-
ent input functions. See Multi Opera-
tion and System Off on page 67.
Setting What it does
SYSTEM
OFF
This is a function for automatically
turning off the power of devices con-
nected to the receiver. Multiple remote
control codes can be set, as desired.
See Multi Operation and System Off on
page 67.
DIRECT
FUNC
This is a setting for changing only the
remote control unit’s operation screen,
without changing the receiver’s input,
when the remote control unit’s input
function buttons are pressed. This
is convenient for using the remote
control unit for devices not connected
to the receiver. See Direct function on
page 66.
RENAME
The names of the input function but-
tons displayed on the remote control
unit can be changed as desired. See
Renaming input function names manu-
ally on page 66.
SYNC
RENAMING
Input function names changed on the
receiver can be acquired by the remote
control unit so that the names are the
same on the remote control unit. See
Renaming input function names in syn-
chrony with the receiver on page 72.
ERASE
LEARNING
This function is used to erase remote
control codes that have been learned.
Codes learned for the different input
functions can be erased individually.
See Erasing one of the remote control
button settings on page 66.
IR/RF
SELECT
This function is for selecting wireless
(RF) or infrared (IR) as the remote
control operating mode for the different
devices. See Operating this receiver by
RF communications on page 71 and
Operating other components by RF com-
munications on page 71.