Vaddio CeilingVIEW HD HideAway - Manual (Page 18)

CeilingVIEW HD HideAway Manual
CeilingVIEW HD HideAway Manual, Document Number 342-0289 Rev. B Page 18 of 24
Quick-Connect
DVI/HDMI-SR
Interface
Lift Contact:
Open-Lift Up
Closed-Lift Down
Polycom
HDX-8000
Series Codec
Polycom HDX-
8000 Series IR
Remote Control
Note: A Vaddio
ClearVIEW HD-19 PTZ
Camera is inside the
CeilingVIEW HD
HideAway
Vaddio IR
Commander
Remote Control
Examples of Integrating the CeilingVIEW HD HideAway with Polycom® or TANDBERG (Cisco®) Codecs:
Figure 28; Example 1: Polycom Codec:
Integration of the CeilingVIEW HD HideAway Motorized Lift, CeilingVIEW HD
HideAway Power Interface, Vaddio HD-19 PTZ Camera, Quick-Connect DVI/HDMI SR and a Polycom Codec with Polycom IR
Remote Control.
 To add the Vaddio ClearVIEW HD PTZ Camera video image and IR control of the Vaddio HD PTZ Camera, it
will be necessary to connect a Polycom Breakout Cable (PN 235-21-001) to one of the camera input ports on
the Polycom Codec. The Polycom Breakout Cable provides RS-232/IR and component video connectivity to
the Vaddio Quick Connect DVI/HDMI SR Interface (see Figure 28). Installation of a Vaddio RJ-45 to DB9
Adapter (PN 998-1006-232) will provide connectivity of the Polycom IR Remote Control commands (Power
on/off and PTZ commands) to the Vaddio Quick-Connect DVI/HDMI-SR and on to the CeilingVIEW HD
HideAway.
 The CeilingVIEW HD HideAway can be activated and controlled in two ways:
1) Provide a latched contact closure to the Lift Contact pair on the CeilingVIEW HD HideAway Power
Interface (PN 998-2520-002) in order to lower the Vaddio HD PTZ Camera in the CeilingVIEW HD
HideAway. The latched closure can be provided by a control system or a simple manual switch
connected to the Lift Contact pair. As the Vaddio HD PTZ Camera is lowered by latching the Lift Contact,
it will power up and go to its home position. Once the lift has stopped, the Vaddio HD PTZ Camera will
receive PTZ commands from the Polycom IR Remote or the Vaddio IR Remote Commander.
Note 1: The Vaddio IR Remote Commander must be pointed to the front of the Vaddio HD PTZ Camera
(IR receiver location) in order to be received by the camera in order to control PTZ functions.
Note 2: The Polycom IR Remote must be pointed at the front of the Polycom Codec (IR Receiver
location) to control the CeilingVIEW HD HideAway and the Vaddio HD PTZ Camera.
2) Use the Power Button (green) on the Vaddio IR Remote Commander to power the CeilingVIEW HD
HideAway on and lower the camera lift (see Figure 22). The Vaddio IR Remote Commander must be
pointed to the CeilingVIEW HD HideAway (in the direction of the IR Sensor in the Trim Plate Assembly
(see Figure 23) to activate the CeilingVIEW HD HideAway and lower the camera lift. Once the camera lift
Power to Camera,
HD Video Returned
Lift Power and Lift Contact
CeilingVIEW HD
HideAway
Power Interface
Camera
Control
RS-232
Three (3) Cat-5e Cables
Up to 100’ (30.4m)
¾” Conduit
Connector
CeilingVIEW HD
HideAway
Motorized Lift
System
IR/RS-232
YPbPr
Polycom
Breakout Cable
(PN 235-21-001)
Vaddio
RJ-45 to DB9
Series Adapter
(PN 998-1006-232)
YPbPr