Rd / ru, Pc control command reference guide – Kenwood TS-990S User Manual
Page 49
– 48 –
PC Control Command referenCe guide
QI
Writing the Quick Memory
Parameters:
No parameters are used with this command.
• Performs the same function as pressing [Q-M.IN].
• When the AI function is ON, a response is output when writing
to the Quick Memory.
Set
1
2
3
4
5
6
7
8
9
10
Q
I
;
Read
1
2
3
4
5
6
7
8
9
10
Q
I
;
QR
Quick Memory
Parameters:
P1
0: Quick Memory OFF
1: Quick Memory ON
P2
0 ~ 9: Quick Memory channel number
(If parameter P1=0, set parameter P2 to 0. When selecting Quick
Memory ON but not setting a channel number, this setting is
blank.)
• When configuring a value above the number of Quick Memory
channels set by the menu, an error occurs.
• When specifying a blank channel, an error occurs.
Set
1
2
3
4
5
6
7
8
9
10
Q
R
P1
P2
;
Read
1
2
3
4
5
6
7
8
9
10
Q
R
;
Answer
1
2
3
4
5
6
7
8
9
10
Q
R
P1
P2
;
RA
Attenuator
Parameters:
P1
0: Main Band
1: Sub Band
(This parameter is invalid during the Setting command; the
operating band is always selected. Enter any value.)
P2
0: ATT OFF
1: -6 dB
2: -12 dB
3: -18 dB
Set
1
2
3
4
5
6
7
8
9
10
R
A
P1
P2
;
Read
1
2
3
4
5
6
7
8
9
10
R
A
P1
;
Answer
1
2
3
4
5
6
7
8
9
10
R
A
P1
P2
;
RC
RIT/XIT Frequency Clear
Parameters:
No parameters are used with this command.
• Clears the RIT/XIT frequency regardless if the RIT/XIT function
is ON or OFF.
Set
1
2
3
4
5
6
7
8
9
10
R
C
;
RD / RU
RIT/XIT Frequency Up/ Down
Parameters:
P1 (Set 2 command only)
00000 ~ 09999: Frequency (in Hz)
• Use setting 1 to adjust the frequency by 1 step.
• The RU command is used to increase the frequency and the
RD command is used to decrease the frequency.
• Use the setting 2 to set a RIT/XIT frequency via the P1
paramter. Use the RU command to enter a positive frequency
and the RD command to enter a negative frequency.
Set 1
1
2
3
4
5
6
7
8
9
10
R
D / U
;
Set 2
1
2
3
4
5
6
7
8
9
10
R
D / U P1
P1
P1
P1
P1
;
RE
Recording Function
Parameters:
P1
0: Recording/Playback stop
1: Begin normal recording/recording in progress
2: Recording storage (setting only)
3: Begin quick playback/playback in progress
4: Pause normal recording/resume recording
5: Pause quick playback/resume playback
6: Recording failure (response only)
7: Playback failure (response only)
(The AI function will not perform an auto response when a
recording or playback failure occurs due to the operation of the
transceiver.)
P2
001 ~ 100: Playback progression (000 when no playback is in
progress.)
(The AI function performs an auto response every second for the
playback progression.)
Set
1
2
3
4
5
6
7
8
9
10
R
E
P1
;
Read
1
2
3
4
5
6
7
8
9
10
R
E
;
Answer
1
2
3
4
5
6
7
8
9
10
R
E
P1
P2
P2
P2
;