Pc control command reference guide – Kenwood TS-990S User Manual
Page 17
– 16 –
PC Control Command referenCe guide
DD1
Scope Display Data Output Control (Sub-Scope Display
Information Setting)
Parameters:
P1
0: No Output
1: High-Speed Output (for LAN connection)
2: Low-Speed Output (for COM connection)
(High-speed output and low-speed output cannot be used
simultaneously.)
Set
1
2
3
4
5
6
7
8
9
10
D
D
1
P1
;
Read
1
2
3
4
5
6
7
8
9
10
D
D
1
;
Answer
1
2
3
4
5
6
7
8
9
10
D
D
1
P1
;
DD2
Display Data Output Control (Bandscope Display Information) Parameters:
P1
00 ~ 31: Split Number
P2
Bandscope Spectrum Display Information (40 digits)
20 spectrum information are each expressed as 2 ASCII digits.
Two digits of the beginning of division No. 00 are spectrum
information of the left side, and two digits of the end of division
No. 31 become the spectrum information of the right side.
The range of value for each spectrum information is from 00h ~
8Ch (hexadecimal numbering).
00h shows the state where the spectrum is extended to the
top (signal strength = 0 dB) and 8Ch shows a state where the
spectrum is not displayed (signal strength = -100 dB).
The respective spectrum information is converted to ASCII code
of the hexadecimal number of from the upper byte digits. For
8Ch, the order becomes “8”, “C”.
• When the AI functions sets the speed as low when using
the DD0 command, it is output from division No. 00 to 31,
sequentially.
• When the transceiver is not displaying the bandscope, it is not
output.
• This command operates only at a baud rate of 115200 bps.
• It is possible to perform high-speed control using the ##DD2
command exclusively for a LAN.
Answer
1
2
3
4
5
6 ~ 45
46
47
48
D
D
2
P1
P1
P2
;
DD3
Display Data Output Control (Subscope Display Information)
Parameters:
P1
00 ~ 14: Split Number
P2
Subscope Spectrum Display Information (38 digits)
19 spectrum information are each expressed as 2 ASCII digits.
Two digits of the beginning of division No. 00 are spectrum
information of the left side, and two digits of the end of division
No. 14 become the spectrum information of the right side.
The range of value for each spectrum information is from 00h ~
32h (hexadecimal numbering).
00h shows the state where the spectrum is extended to the
top (signal strength = 0 dB) and 32h shows a state where the
spectrum is not displayed (signal strength = -50 dB).
The respective spectrum information is converted to ASCII code
of the hexadecimal number of from the upper byte digits. For
32h, the order becomes “3”, “2”.
• When the AI functions sets the speed as low when using
the DD1 command, it is output from division No. 00 to 14,
sequentially.
• When the transceiver is not displaying the subscope, it is not
output.
• This command operates only at a baud rate of 115200 bps.
• It is possible to perform high-speed control using the ##DD3
command exclusively for a LAN.
Answer
1
2
3
4
5
6 ~ 44
45
46
47
D
D
3
P1
P1
P2
;
DF
∆F Display
Parameters:
P1
0: No ∆F Display Information
1: ∆F Display Information (during split mode or split frequency
operation)
P2
0: Plus
1: Minus
(When P1 is 0, P2 also becomes 0.)
P3
11 digit frequency in Hz (enter unused digits as 0)
(When P1 is set to 0, all digits are returned as 0.)
Read
1
2
3
4
5
6
7
8
9
10
D
F
;
Answer
1
2
3
4
5
6
7
8
9
10
D
F
P1
P2
P3
P3
P3
P3
P3
P3
11
12
13
14
15
16
17
18
19
20
P3
P3
P3
P3
P3
P3
P3
;