Basic operation of hands-free phoning (model-b), Before use, Making a call – Kenwood KCA-BT200 User Manual
Page 6
6
|
KCA-BT200
Before Use
• You need to register your cell-phone before using
it with this unit. For more details, see
• If you have registered two or more cell-phones,
you need to select one of them. For more details,
see
• To use the Phone Book, it must be downloaded to
this unit in advance. For details, see
• For the method of operation in the Function control,
refer to the Instruction Manual for Control Unit.
• For more information regarding the function with
[
] mark, see
Making a call
Dialing Method
1. Entry dialing method mode
Press the [ATT] button for at least 1 second.
2. Select a dialing method
Press the Control knob ([
38]).
"DIAL" » "INITIAL" » "P-BOOK" » "OUT-CALL" » "IN-
CALL" » "MIS-CALL"
3
Methods of operations in the above modes are
described below.
3. Exit the dialing method selection mode
Press the [ATT] button for at least 1 second.
3
Dial a number (
)
2-1. Select the "DIAL" display.
2-2. Enter a phone number
Press the number ([1] – [0]), #([FM]), *([AM]), or
+([
¢]) button on the remote controller.
2-3. Make a call
Press the [DIRECT] button on the remote controller.
☞ You can input max 32 digits.
3
Speed dialing (Preset dial)
2-1. Select the "DIAL" display.
2-2. Select the preset dial number
Model
B-1:
Press the [1] – [6] button.
Model
B-2:
2-1. Press the [FNC] button.
2-2. Select the number to recall by turning the
Control knob.
2-3. Press the Control knob.
2-3. Make a call
Press the Control knob ([
38]) for at least 1 second.
☞ You need to register the preset dial number. (page 7)
Basic Operation of hands-free phoning (Model-B)
3
Calling a number in the call log (
)
2-1. Select the "OUT-CALL" (outgoing call), "IN-CALL"
(incoming call), or "MIS-CALL" (missed call) display.
2-2. Select a name or phone number
Push the Control knob towards up or down.
2-3. Make a call
Press the Control knob ([
38]) for at least 1 second.
3
Calling a number in the Phone Book (
)
2-1. Select the "INITIAL" display, proceed to step 2-2.
Select the "P-BOOK" display, proceed to step 2-3.
2-2. Select the initial to be searched for
Operation type
Operation
Move to the next
character.
Push the Control knob towards right or left.
Move to the next row. Push the Control knob towards up or down.
Determine the
selected initial
Press the Control knob ([
38]).
2-3. Select the name
Operation type
Operation
Change the name.
Push the Control knob towards up or down.
Change the initial.
Push the Control knob towards right or left.
2-4. Make a call
Press the Control knob ([
38]) for at least 1 second.
Make a voice dialing call
1. Select voice recognize item during Function
control
Select "BT" > “V-REC“.
2. Press the Control knob ([
38]).
"PB Name?" is displayed.
When a beep is heard, utter the name within 2
seconds.
3. "PN Type?" is displayed.
When a beep is heard, utter the category within 2
seconds.
4. Make a call
This step is the same as step 3 of the procedure in
make a call or select a category.
☞ If your voice cannot be recognized, a message is
displayed. Pressing the [
38] button allows you to retry
voice input. (page 26)
☞ Both the name and category requires registration of a
voice tag. (page 15)
☞ Audio sound is not output during voice recognize.
Display of phone number type (category)
Display
Description
Display
Description
"General"/
General
"Office"/
Office
"Home"/
Home
"Other"/
Other
"Mobile"/
Mobile
B64-4121-10_01_KE.indb 6
B64-4121-10_01_KE.indb 6
08.2.25 2:10:16 PM
08.2.25 2:10:16 PM