Summers 84' Superroller - Manual (Page 25)

SECTION 2 - ASSEMBLY
Hydraulic Installation
H1. Install Hydraulic components as shown in Figure 7 provided.
A. Leave enough slack at all pivot points to allow folding machine without stretching or pinching
hydraulic hoses.
B. Secure hoses with nylon ties and clamps provided. Do not over tighten clamps.
H2. Install 8J5300 (one to each port) on front cylinder. Install 8J5700 to each end of tees. Attach 8N3312
(312” hoses) to bottom 8J5700 on each port of front cylinder and run forward to the hitch leaving
enough slack in hose by cylinders for movement.
H3. Install 8N3432 (432” hose) to 8J6000 (90° fitting). Attach 8J6000 to 8J5300 on center port. Hydraulic
Tees should be centered on machine as shown in Figure 7 - Detail F.
H4. Attach one end of 8N2088 (88” hose) to 8J5300 on center port and connect other end to 8J6010 on
inside port of folding folding cylinder on first section of landroller. Attach one end of 8N0276 (276”
hose) to 8J5300 on tee and connect other end to 8J6010 on outside port of folding cylinder of first
section. (See Figure 7 - Detail C)
H5. Attach 8J5620 to both ports on center rear lift cylinder. Install 8C0650 (manifold) to each port accord-
ing to Figure 7 - Detail A. Install 8J5500 on center port of top 8C0650 and all three ports of bottom
8C0650 (as shown in Figure 7 - Detail A).
H6. Install 8N3150 to 8J5700 on top port of front cylinder. Attach other end to center port of top 8C0650
(manifold). Install 8N3156 to 8J5700 on bottom port of front cylinder. Attach other end to center port
of bottom 8C0650 (manifold). Run both hoses along frame as shown in Figure 7.
H7. Attach one each 8N3276 for 62’ (or 8N3312 for 84’) to each of the outside ports on both 8C0650
(manifold) as shown in Figure 7 - Detail A. Run hoses along frame as shown in Figure 7 toward lift
cylinder on first section. Attach 8J5620 to each port on cylinders. Attach center port of 8J5700 (tee)
to each 8J5620 on lift cylinder. Attach end of hose to one port of tee.
H8. Attach 8N3252 for 62’ (or 8N3276 for 84’) to other side of tee on section 1 lift cylinder. Run along
frame as shown in Figure 7. Attach 8J6010 to each port on rear lift cylinder as shown in Figure 7 -
Detail E. Attach other end of 8N3252 to each port of rear lift cylinder.
H9. Install two 8P6010 into each port on the pivot lock cylinder.
62 Ft. LandRoller: Attach 8N3534 to each port of cylinder and route hose toward the front of the
machine as shown in Figure 7.
84 Ft. LandRoller: Attach 8N3136 to each port of cylinder and route hose towards the front of the
machine as shown in Figure 7. Using 8J5100 attach the 8N3534 and continue running the hose to-
wards the front of the machine.
Attach 8J5300 to the end of the 8N3534 and join the hose from each side of the machine together
with the tee. Attach 8N3432 to the remaining port and run the hose towards the front of the machine
as shown.
Install the adapter fitting and hydraulic tips as shown.
H9. Secure all hoses with hose hold downs and zip ties, leaving slack in hose near pivot points and cylin-
ders.
2-15