Posey Drop Seat - Manual

Seating and PoSitioning Quality Products since 1937
M1631 051209
#7020F
#654018/654020
Drop Seat
These adjustable drop seats lower the wheelchair seat so the patient’s feet
can touch the floor. They attach to the wheelchair seat frame using
polypropylene straps and square metal rings. The seat height may be
lowered from 1/4” (5/8 cm) to 3” (8 cm) depending on the wheelchair model,
and/or can be adjusted to create a “tilt” or “wedge effect” to help prevent
forward sliding. Made of durable, wipe-clean polyvinylchloride (PVC).
• No tools required to adjust seat height.
REF
654018 Fits most 18” (46 cm) wheelchairs
REF
654020 Fits most 20” (51 cm) wheelchairs
application inStructionS:
1. Remove the vinyl seat of the wheelchair by unscrewing the seat screws.
2. Release the polypropylene straps of the Drop Seat from the
square loop rings.
3. Orient the Drop Seat to the wheelchair as shown in the photo. Wrap
each end of the polypropylene straps (on each side of the chair)
around the metal bar of the seat frame and thread back through the
slot, pulling the ends toward the center of the Drop Seat (Fig. 1).
4. Attach the straps underneath the seat using the square loop
rings. (Fig. 2). All straps should pass under the Drop Seat.
Fig. 1 Fig. 2
Wheelchair bar
(seat frame)
Drop Seat
THREADING STRAP THROUGH DROP SEAT
7+5($',1*
7+528*+648$5(
/2235,1*6
7+5($',1*
7+528*+648$5(
/2235,1*6
Drop Seat cuShion
This cushion is specially designed to fit the Posey 654018
Drop Seat only for 18” (46 cm) wheelchairs. Made of durable
polyurethane foam and covered in blue vinyl. This cushion
has notches cut out to fit over the cross bars.
REF
7020F 15½” x 16” x 2” thick (39 cm x 41 cm x 5 cm)
LATEX
inSpection
Inspect before each use: check for broken stitches
or parts; torn, cut or frayed material; or buckles that do not hold
securely. DO NOT use soiled or damaged products.
MonitorinG
Always follow your facility’s policies and procedures for
patient assessment, monitoring and rehabilitation
5. Adjust the polypropylene straps so the Drop Seat is at the
desired height (If desired, straps may be adjusted to create a
“wedge”).
6. Test the attachment for strength and security by applying
weight with your foot, knee or hand down on the seat.
DO NOT sit down until you have made sure the
attachment is secure!
7. Insert a cushion on top of the Drop Seat to ensure patient
comfort and proper positioning.
DO NOT use the Drop Seat without a cushion!
NOTE: When installed and used properly, this product has a
weight capacity of 250 lbs. (113 kgs.).
DiSpoSal
Properly dispose of the product per facility’s policy for
BIOHAZARDOUS materials.
StoraGe anD hanDlinG
This device is designed for use in normal indoor environments.
This device may be stored in ambient warehouse temperatures at
normal humidity levels. Avoid excess moisture or high humidity
that may damage product materials.
application inStructionS
1. Make sure the cushion dimensions match those of the wheelchair.
2. Place cushion on the wheelchair seating surface.
3. Align the front edge of the cushion with the front edge of the
wheelchair seat.
cleaninG inStructionS:
• Wipe Clean with mild detergent. OSHA approved intermediate level disinfectants can be used per manufacturer instructions.
DO NOT use phenol and benzyl based disinfectants.
• After cleaning, products MUST be rinsed with water to remove any residual chemicals.
• Make sure products are completely dry before use.
Posey Company • 5635 Peck Road, Arcadia, CA 91006-0020 USA
Phone: 1.800.447.6739 • Fax: 1.800.767.3933 • Web: www.posey.com
© 2009 Posey Company. All rights reserved.
Posey
®
Drop Seat/Cushion