Posey Seizure Side Rail Pads - Manual

© 2011 Posey Company. All rights reserved. M6132 REV C 040411
Posey Company • 5635 Peck Road, Arcadia, CA 91006-0020 USA • www.posey.com
Phone: 1.800.447.6739 or 1.626.443.3143 • Fax: 1.800.767.3933 or 1.626.443.5014
Model 5743 - Hill-Rom ® VersaCare® Bed
Model 5755 - Stryker ® Secure I & II® with Rounded Side Rails
Fig. 2
Fig. 3
Posey Seizure Pads are form fitted to fit snugly over the existing bed side
rails with a 1” (3 cm) layer of medium density foam to help safeguard
against accidental patient injury. The outer shell is constructed from
lightweight sheer nylon denier to help prevent patient “rub” burns and
allows unobstructed movement of the side rails to the lowered position.
The nylon cover is backed with a urethane waterproof coating that easily
wipes clean with liquid disinfectant. Open windows in upper section allow
for easy access to controls on most bed models. Navy Blue. Meets CA #117,
Section E Flame Retardancy Standards.
Cat. No. Description
Pads
hill-rom® Beds
REF 5725 Fits Advanta™ and Century Plus® beds 4
REF 5729 Fits Advanta™ (Pre- 02/2004), Advance®, Century 8500,
and Century CC Beds 4
REF 5742 Fits CareAssist® and Advanta™ 2 Beds 4
REF 5743 Fits VersaCare® Med / Surg Beds 4
REF 5744 Fits Affinity III® and IV® Maternity Beds 2
REF 5746 Fits TotalCare® Med / Surg Beds 4
REF 5747 Fits Resident® LTC Beds 2
REF 5760 Fits Hill-Rom Low® Beds 2
REF 5761 Fits Affinity II® Maternity Beds 2
stryker® Beds
REF 5755 Fits Secure I and II® Beds with Rounded Side Rails 4
REF 5762 Fits Secure I and II® Beds with Rectangular Side Rails 4
REF 5763 Fits GO Bed II® with Rectangular Side Rails 4
REF 5764 Fits In-Touch™ Critical Care Beds 4
REF 5766 Fits S3™ Beds 4
other manufacturers
REF 5760 Fits Carroll® Beds with Care Assist Arms 2
REF 5765 Fits Med-Mizer® Beds with Med Support Arms 2
monitoring
Posey Seizure Side Rail Pads will not prevent a determined
patient from exiting the bed, going over or attempting to go between or
through side rail gaps. Not all hospital beds allow for full articulation
when this product is applied. Slowly articulate the head of the bed to
ensure compatibility. AlwAys follow your facility’s policies and
procedures for patient assessment, monitoring and rehabilitation.
application instructions:
1. Inspect product prior to use. DO NOT use soiled or damaged products.
2. Identify each of the components in the set. Each pad has sewn-in tags,
identifying its intended location from the perspective of lying down in
the bed (Fig. 1).
3. Slip each of the pads onto the proper side rail and move it into
position (Fig. 2).
4. Securely fasten all the hook and loop fasteners along the bottom edge
of each pad. Some pads may have an additional hook and loop fastener
in their mid-section (Fig. 3).
5. Lower each of the side rails to check clearances. Note that there may be
some resistance as the rails are completely lowered. This should be
expected as there are close manu facturing tolerances between the bed
and the side rail. The shear nylon covers are chosen to minimize any
potential binding.
6. Check for proper fit. Modified beds may not be compatible with Posey
Seizure Side Rail Pads.
Fig. 1
Advance, Advanta, Affinity, CareAssist, Century Plus, Resident, TotalCare and VersaCare, are registered
trademarks of Hill-Rom® Services, Inc. Med-Mizer is a registered trademark of Med-Mizer Inc. Go-Bed II,
In-Touch, Secure, S3 and Stryker are registered trademarks of the Stryker® Corporation.
cleaning instructions:
Wipe clean with soap and water or disinfectant.
DO NOT use cleaners that contain Phenol or Benzyl.
disposal
Properly dispose of the product per facility’s
policy for BIOHAZARDOUS materials.
storage and handling
This device is designed for use in normal indoor environments.
This device may be stored in ambient warehouse temperatures
at normal humidity levels. Avoid excess moisture or high
humidity that may damage product materials.
Posey
®
seizure side rail Pads
BeD sAFety