Actron CP7999 - Manual

1
The manufacturer produces a full line of gauges with many dif
ferent styles.
1-1/2" Gauges
2” Gauges
2-5/8" Gauges
(See page 2 for hole sizes.)
MICROPROCESSOR-CONTROLLED ENGINES
3.
It is recommended that the battery ground cable be disconnected before any electrical work is performed, especially when installing Ammeters or V
oltmeters.
4
.
Route all wiring and gauge tubing away from
linkages, high heat or moving parts.
5
.
Never smoke while working on your vehicle
and always keep a fire extinguisher nearby
.
It should be rated for gas/chemical/electrical fires.
6
.
Never lay tools on top of the battery or wear
jewelry during .electrical work to avoid severe electrical shorts.
1
.
Read the entire instructions for your gauge
before proceeding.
2
.
Be sure the gauge is suitable for your vehicle: •
Does the gauge’
s range cover the vehicle’
s
operating range?
•
Will the tubing of the mechanical gauges reach from the engine connection point to the gauge (temperature gauges cannot be length- ened)?
•
Is the vehicle’
s electrical system 12 volt and
negatively grounded?
INST
ALLA
TION & SAFETY PRECAUTIONS
INSTALLATION INSTRUCTIONS
GENERAL MOUNTING INSTRUCTIONS
GAUGE
DASHBOARD
BRACKET
NUTS &
W
ASHERS
Top V
iew
Diagram 1
GAUGE MOUNTING
Gauges allow you to monitor the condition of your vehicle and tell how well it is performing. If there are any problems, you can detect them immedi- ately before they become severe. W
arning lights
only tell you when the problem already requires immediate attention. Y
ou will find that the addi-
tion of these gauges will add to your peace of mind and driving comfort.
Many newer vehicles employ microprocessors that control most of the engine and electrical func- tions. Microprocessors are very sensitive electri- cal components. Before installing any aftermar- ket equipment consult the vehicle’
s manufacturer
or shop manual to make certain that no damage will result. Some of these newer vehicles use electric cool- ing fans or microprocessor engine controls that depend on readings from the original equipment
sending units for correct operation. If your vehicle is one of these you CANNOT replace the sender(s) with any other
. Y
ou can add an addi-
tional oil pressure sender with a “T
ee Adapter Kit,”
but the only possible way to install a non OEM water temperature sender is to install the new sender in a dif
ferent location, retaining the OEM
unit in its original location. Check with the vehicle’
s
manufacturer or dealer to see if this is possible.
All gauges can be mounted into a surface of your choice or into a panel. Single, dual & triple gauge mounting panels are produced for all size gauges. Some panels are in black or chrome finishes. A fully chromed mounting cup is available for the 2-5/8" gauges. 1
.
Choose a location to mount the gauge where
it will be viewable from a normal driving posi- tion (fuel pressure gauges should never be mounted within the interior of the vehicle).
2
.
If you are using a mounting panel, mount it at
the chosen location with the screws provided.
If you are creating a hole, use the following sizes:
Gauge Style
Hole Size
1-1/2"
1-5/8" (41 mm)
2
"
2-1/16" (53 mm)
2-5/8"
2-5/8" (67 mm)
8
FULL ONE (1) YEAR W
ARRANTY
ACTRON MANUF
ACTURING CO.
15825 Industrial Parkway Cleveland, Ohio 44135
©
2002 Actron Manufacturing Co.
0002-000-2376
© 2002 Actron Manufacturing Co. Product manufactured in China to Actron Mfg. Co.specifications
Actron Manufacturing Company
, 15825 Industrial Parkway
, Cleveland, Ohio 44135, warrants to the user that this
unit will be free from defects in materials and workmanship for a period of one (1) year from the date of original purchase. Any unit that fails within this period will be repaired or replaced at Actron’
s option and without charge when
returned to the Factory
. Actron requests that a copy of the original, dated sales receipt be returned with the unit
to determine if the warranty period is still in ef
fect.
This warranty does not apply to damages caused by accident, alterations, or improper or unreasonable use. Expendable items, such as batteries, fuses, lamp bulbs, flash tubes are also excluded from this warranty
.
ACTRON MANUF
ACTURING COMP
ANY DISCLAIMS ANY LIABILITY FOR INCIDENT
AL OR CONSEQUEN-
TIAL DAMAGES FOR BREACH OF ANY WRITTEN W
A
RRANTY ON THE UNIT
. Some states do not allow the
disclaimer of liability for incidental or consequential damages, so the above disclaimer may or may not apply to you. This warranty gives specific legal rights, and you may also have rights which vary from state to state.
GARANTIA COMPLET
A POR UN (1) AÑO
Actron Manufacturing Company
, 15825 Industrial Parkway
, Cleveland, Ohio 44135, garantiza al usuario que
esta unidad estará libre de defectos de materiales y mano de obra por un período de un (1) año a partir de la fecha original de compra. Toda unidad que falle dentro de este período será reparada o reemplazada a la opción de Actron y sin cargo cuando sea devuelta a la fábrica. Actron requiere que se devuelva una copia del recibo original fechado de compra con la unidad, para determinar si el período de garantía está todavía en efecto. Esta garantía no se aplica a daños causados por accidentes, modificaciones, o uso inadecuado o irrazonable. Los artículos descartables tales como pilas, fusibles, bulbos de lámparas, tubos flash se excluyen también de esta garantía. ACTRON MANUF
ACTURING COMP
ANY NIEGA CUALQUIER RESPONSABILIDAD POR PERJUICIOS
INCIDENT
ALES O CONSECUENTES POR VIOLACION DE CUALQUIER GARANTIA ESCRIT
A P
ARA LA
UNIDAD. Algunos estados no permiten la negación de responsabilidad por perjuicios incidentales o consecuentes, de manera que la negativa anterior puede o no aplicarse a usted. Esta garantía otorga derechos legales específicos, y usted puede tener también derechos que pueden variar de estado a estado.
© 2002 Actron Manufacturing Co. Producto fabricado en China bajo las especificaciones de Actron Mfg. Co.
Actron Manufacturing Company
, 15825 Industrial Parkway
, Cleveland, Ohio 44135, garantit à l'utilisateur que
cet appareil sera exempt de tout défaut lié aux matériaux ou à la main d'œuvre pendant une période de un (1) an à compter de la date d'achat d'origine. Toute unité qui tomberait en panne durant cette période sera réparée ou remplacée, au choix d'Actron, et sans frais si elle a été retournée à l'usine. Actron demande qu'une copie de la facture d'achat d'origine datée soit retournée avec l'appareil pour contrôler que la période de garantie est toujours ef
fective.
Cette garantie ne s'applique pas aux dommages causés par accident, modifications ou utilisation inadéquate ou hors du raisonnable. Les éléments consommables, tels que piles, fusibles, ampoules ou tubes fluorescents sont également exclus de cette garantie. ACTRON MANUF
ACTURING COMP
ANY REJETTE T
OUTE RESPONSABILITÉ POUR DOMMAGES
ACCESSOIRES OU INDIRECTS POUR MANQUEMENT À N'IMPOR
TE QUELLE GARANTIE ÉCRITE SUR
CETTE UNITÉ. Certains états ne permettent pas le déni de responsabilité pour dommages accessoires ou indirects, cette clause peut donc n'être pas applicable dans votre cas. Cette garantie vous octroie des droits légaux spécifiques, et vous pouvez aussi avoir des droits supplémentaires qui varient d'un état à l'autre.
UN (1) AN DE GARANTIE COMPLÈTE
© 2002 Actron Manufacturing Co. Produits fabriqués en Chine suivant les spécifications Actron