Pypes Performance Exhaust SGT29V - Manual

SGT29V
409 Stainless Steel Cat-Back Exhaust System for
2009-13 GM 1500 Series Pick-ups
Before you begin please READ all instructions and confirm that all
components where received in your new Pypes Performance Exhaust Cat-
Back systems. If you find a component missing or have questions about the
installation please contact our tech department by email at
[email protected] or by phone at (800) 421-390 or by viewing our
installation gallery on our website www.pypesexhaust.com
Pypes Performance Exhaust
2705 Clemens Road Suite B103 Hatfield, PA 19440
800-421-3890 (voice) 215-712-9968 (fax)
www.pypesexhaust.com
PLEASE TRY INSTALLING OUR WAY FIRST!
1. Begin by placing the vehicle on a lift or four jack stands at there maximum height. To help your installation it is best to pre-fit all
the components into a complete system on your garage floor using the diagram provided.
2. Remove the existing system by cutting the mid-pipe as close to the front side of the muffler as possible. Remove the tailpipe
from the insulator and the entire unit can be removed as one. Depending on the working conditions you may need to make other cuts to
remove the system. Make sure you retain the rubber insulators because it will be reused.
3. Begin your installation by reinstalling the factory rubber isolators onto the wire
forms near muffler and factory tailpipe locations. Next install the HVH60R to HVH60
hanger and mount the assembly using the supplied hardware to the large hole in the rear
left side frame rail. The HVH60 opening should face the outside of the vehicle.
4. Next install the TGT29R tailpipe on the passenger side using the reinstalled
rubber insulators. Next install the TGT29LR then the TGT29LF using one of the HVC50
clamps. Do not tighten clamp at this time.
5. Loosely install the MVV71 muffler and MGT29 mid-pipe and mark the factory
mid-pipe so you can make your final cut making sure you leave enough material to com-
pensate for the slip fit connections. Remember measure five times and cut once.
6. Now you can permanently install the muffler and mid-pipe using the HVC26 band
clamp for the mid-pipe to mid-pipe connection, the HVC53 U-clamp for the mid-pipe to
muffler connection and the remaining two HVC50 U-clamps for the muffler to tailpipe connections.
7. Lastly install the EVT51B tips using the two HVC21 band clamps.
8. Finish the system by making all your final adjustment to the muffler, tailpipes and tips. Once you are satisfied with the align-
ment finish tightening all the clamps. The use of air tools for this step is highly recommended. Next start your vehicle and check for
leaks. All clamps should be checked within the first 100 miles of driving and retightened as necessary.
Note:
Pypes Performance Exhaust Cat-Back systems are designed to fit stock height vehicles with OEM hitches and spare tire
combos. Vehicles with aftermarket components such as larger trailer hitches and spare tires or ride height changes may require modifi-
cations to the system for proper fit.
Now it’s time to fire up that truck and enjoy your
new Pypes Performance Exhaust.
Bill of materials:
1 pr EVT51B Tips
1 ea MGT29 Mid Pipe
1 ea TGT29LF Tail Pipe
1 ea TGT29LR Tail Pipe
1 ea TGT29R Tail Pipe
1 ea MVV71 Violator Muffler
3 ea HVC50 2.5” U-Clamp
1 ea HVC51 3” U-Clamp
2 ea HVC21 2.5” Band Clamp
1 ea HVC26 2.75” Band Clamp
1 ea HVH60 Tail Pipe Hanger
2 ea HVH60R Hanger Insulator
1 ea 3/8x1.5 Hex Bolt
1 ea 3/8 Nylock Hex Nut