Pypes Performance Exhaust SFM76M - Manual

1. Begin by placing the vehicle on a lift or on four jack stands at
maximum height. This will aid in and easier installation.
2. Unbolt the factory axleback at the clamp using a 13mm socket.
Spray the rubber hangers with penetrating oil to aid in the removal of the
factory mufflers.
3. Using a 15mm socket loosen the 2 band clamps that connect the
factory mid pipe to the back of the factory H-pipe. These clamps will be
reused with your new system. DO NOT loosen the ball and socket clamps
before the H-pipe.
4. Now you can remove the factory system by starting with the mid
pipes followed by the axleback. Note there is no need to remove the fac-
tory hangers for this operation.
5. Now it’s time to start installing your new cat-back system. Begin
by installing the two 16” TFM62B-2.75 pipes loosely into the 2 recycled
band clamps with the slight bend facing the back of the car.
6. Next install the 3” M80 muffler followed by over the axle pipes
using 4 of the HVC24 band clamps. Do not tighten clamps at this point.
7. Install the Pype Bomb Axleback next by sliding the 2 front wire
forms into the factory rubber hangers, then onto the over the axle tube
and then into the factory hanger at the bumper. The remaining HVC24
band clamps will secure the over the axle pipes to the Pype Bomb.
8. Now that all the components are loosely installed you can start
make adjustments to align the system. Start by rotating the TFM62B-2.75
front pipes so that the mufflers follow the pocket in the fuel tank. The
mufflers will appear to be very close to the driveshaft. That is normal for
this system.
9. Next rotate the over the axle pipes so that the tip is aligned
with the openings in the bumper cover. Once everything is aligned
you can begin tightening the clamps. Slight adjustment maybe
needed as you go so save your final tightening until all your
clearances and adjustments are made.
10. Now that you have everything in line finish tightening
all clamps. Air tool are highly recommended for this step.
11. Lastly start your car and check for leaks. It is not
uncommon for the first few hundred miles to make periodic
adjustments to the system.
NOTE: For customers that have install a 3” X or H pipe
you must order the optional TFM62B-3 front Pipes and two
HVC66 3” butt clamps if you do not already have them to
make the system a direct bolt on.
Now it’s time to fire up that muscle car and
enjoy your new Pypes Performance Exhaust.
SFM76M
SFM76M: 2011-12 5.0 Mustang 3” Super System
Thanks again for purchasing your new stainless steel Pype Performance Ex-
haust Mustang Super System. Please be sure to confirm all the components
in the kit were received in your shipment before beginning installation. If you
find any components missing, please contact our office at 800-421-3890 for
replacement. For a quicker and tighter installation air tools are recommend-
ed. Technical assistance is available both on line at www.pypesexhaust.com
of 800-421-3890.
Pypes Performance Exhaust
2705 Clemens Road Bldg 105A Hatfield, PA 19440
800-421-3890 (voice) 267-638-3507 (fax)
www.pypesexhaust.com
TOOLS REQUIRED:
1 Pair of Jack Stands or a Lift
13mm Socket or Wrench
15mm Socket or Wrench
Penetrating Oil
PARTS LIST:
2- TFM62B-2.75
2- 3” M80 Mufflers
2- TFM62A over axle pipes
2- Pype Bomb Axleback
6- HVC24 Band Clamps