Scsiportwidetransfer, Scsitargetluns, Scsitargets – ATTO Technology 1550D User Manual
Page 40: Serialnumber, Serialportbaudrate, Serialportecho, Snmp, Snmpdumpmib, Snmpextendedtraps, Snmptrapaddress

xi
ATTO Technology Inc. iPBridge Installation and Operation Manual
SCSIPortWideTransfer
Controls the iPBridge attempts to negotiate wide SCSI
transfers with devices on the specified bus.
Default: enabled
set SCSIPortWideTransfer [sb] [enabled | disabled]
get SCSIPortWideTransfer [sb]
SCSITargetLUNs
Controls the maximum number of SCSI LUNs per target
the iPBridge queries during a SCSI bus scan.
Default: 8
set SCSITargetLUNs [sb] [ 8 | 64]
get SCSITargetLUNs [sb]
SCSITargets
Lists the physical devices that are connected and running
on the specified SCSI port.
SCSITargets [sb]
SerialNumber
Displays the serial number of the iPBridge. The serial
number is a 13 character field. The first seven
alphanumeric characters are an abbreviation
representing the product name. The remaining six digits
are the individual iPBridge number.
get SerialNumber
SerialPortBaudRate
Configures the baud rate for the iPBridge RS-232 serial
port. The number of data bits per character is fixed at 8
with no parity.
Default: 115200
set SerialPortBaudRate [2400 | 9600 | 19200 | 38400 |
57600 | 115200]
SaveConfiguration Restart command required
get SerialPortBaudRate
SerialPortEcho
Controls if the iPBridge echoes characters on its RS-232
port. When enabled, all non-control character keyboard
input is output to the display.
Default: enabled
set SerialPortEcho [enabled | disabled]
get SerialPortEcho
SNMP
Controls whether or not SNMP functions on the iPBridge.
Default: enabled
set SNMP [enabled | disabled]
get SNMP
SNMPDumpMIB
Displays the contents of the ATTO iPBridge private
SNMP MIB to the current CLI session. For further
assistance with SNMP, consult your network
administrator.
SNMPDumpMIB
SNMPExtendedTraps
Regulates Extended (i.e., Device Transition and Device
Error) SNMP trap functionality.
Default: disabled
set SNMPExtendedTraps [enabled | disabled]
get SNMPExtendedTraps
SNMPTrapAddress
Regulates or displays IP Trap Addresses and Trap
Levels. Index is a value from 1 to 6. The IP address must
be in the same subnet as the iPBridge, and is the host
that wishes to receive traps. The supported severity
levels required to trigger a trap are: None, All,
Warning, Critical.
Default IP address: 0.0.0.0
Default level: none
set SNMPTrapAddress [index] [xxx.xxx.xxx.xxx] [None |
All | Warning |Critical]
get SNMPTrapAddress [index]
SNMPTraps
is enabled on a data
port, a VLAN ID for that port must be specified. All SNMP
traps are sent with the same VLAN tag.
Default: disabled
set SNMPTraps [enabled |disabled] <[dp1] [VLAN ID]>
get SNMPTraps
SNTP
Controls whether SNTP time server is used.If
enabled on a data port, a VLAN ID for that port must be
specified.
Default: enabled
set SNTP [enabled | disabled] <[dp1] [VLAN ID]>
SaveConfiguration Restart command required
get SNTP
SNTPServer
Controls or displays the main IP address the client uses
to retrieve the SNTP time.
Default: 192.43.244.18
set SNTPServer [xxx.xxx.xxx.xxx]
SaveConfiguration Restart command required
get SNTPServer