Sterlco Micro Series Water Temperature Control Unit - Manual (Page 15)

3200 Series
ACS 3216 Operators Manual 15
and vice versa OP Output power demand re-transmission
none No event connected to the output 2.SRC.A I/O 2 SOURCE
A
AL1 Alarm 1 *
AL2 Alarm 2 * 2.SRC.B I/O 2 SOURCE
B
AL3 Alarm 3 *
AL4 Alarm4 * 2.SRC.C I/O 2 SOURCE
C
ALL.A All alarms
nw.AL Any new alarm
Ct.AL CT alarm, load, leak & overcurrent
Lbr Loop break alarm
Sbr Sensor break alarm
t.End Timer end status
t.run Timer run status
mAn Manual status
rmt.F Remote fail
Pwr.f Power fail
2.SRC.D I/O 2 SOURCE
D
These parameters only appear
when the channel function is a
Digital OP,
i.e. 2.FUNC =
d.Out
Selects an event status to be
connected to the output
channel.
The output status is the result
of an OR of Src A, Src B, Src
C, and Src D
Up to four events can,
therefore, operate the output
prg.e Programmer event.
none Conf
2.PLS OUTPUT
MINIMUM
PULSE TIME Minimum output on/off time.
Only applies to time
proportioning outputs and
prevents relays from switching
too rapidly
0.0 to
150.0
Auto or 1.0 to 150.0 seconds
Auto = 110mS 5.0 sec for
relay
Auto for
logic
Conf
nor Normal 2.SENS SENSE To configure the polarity of
output channel 2
Inv Inverted
nor Conf
0.20 0-20mA output 2 . r n g DC OUTPUT
RANGE To configure 0-20mA or 4-
20mA output
Only appears if the output
module is DC output
4.20 4-20mA output
L3
AA RELAY ‘aa’
Name Scrolling
Display
Parameter Description Value Default Access Level
4.TYPE OUTPUT 4
TYPE Output channel 4 hardware
type reLy Relay output reLy Read only
none Disabled d.OUt Conf
d.OUt Digital output
UP Valve open codes VC and VP only
dwn Valve close codes VC and VP only
Heat Heat output
4.FUNC FUNCTION Output channel 4 function
If the instrument is ordered as
valve positioner (codes VC or
VP), only options available are
,
none, d.out, UP, or
dwn
Note: If output 4 is set to up
ensure the other valve
position output is set to
dwn
and vice versa
CooL Cool output
none No event connected to the output 4.SRC.A I/O 4 SOURCE
A
AL1 Alarm 1 *
AL2 Alarm 2 * 4.SRC.B I/O 4 SOURCE
B
AL3 Alarm 3 *
AL4 Alarm4 * 4.SRC.C I/O 4 SOURCE
C
ALL.A All alarms
nw.AL Any new alarm
Ct.AL CT alarm, load, leak & overcurrent
Lbr Loop break alarm
Sbr Sensor break alarm
t.End Timer end status
t.run Timer run status
mAn Manual status
rmt.F Remote fail
Pwr.f Power fail
4.SRC.D I/O 4 SOURCE
D
These parameters only appear
when the channel function is a
Digital OP,
i.e. 4.FUNC =
d.Out
Selects an event status to be
connected to the output
channel.
The output status is the result
of an OR of Src A, Src B, Src
C, and Src D
Up to four events can,
therefore, operate the output
prg.e Programmer event.
none Conf
4.PLS OUTPUT
MINIMUM
PULSE TIME Minimum output on/off time.
Only applies to time
proportioning outputs and
prevents relays from switching
too rapidly
0.0 to
150.0
0 to 150 seconds 5.0 sec Conf