Sterlco Micro Series Water Temperature Control Unit - Manual (Page 13)

3200 Series
ACS 3216 Operators Manual 13
7.1.1 Master Parameter List
INPUT LIST I N P U T
Name Scrolling Display Parameter Description Value Default Access Level
I N . T Y P INPUT TYPE Selects input linearisation and range See manufacture manual for input types available Conf
L3 R/O
none No units - only for custom linearisation
o C Celsius
o F Fahrenheit
o k Kelvin
U N I T S DISPLAY UNITS Display units shown on the
instrument
PErc %
o C L3
nnnn No DP
nnn.n One DP
D E C . P DISPLAY
POINTS Decimal point position
nn.nn Two DP
nnnn Conf
L3 R/O
M V . H I LINEAR INPUT
HIGH High limit for mV (mA) inputs -10.00 to +80.00mV 80.00 Conf
M V . L o LINEAR INPUT
LOW Low limit for mV (mA) inputs -10.00 to +80.00mV -10.00 Conf
RNG.HI RANGE HIGH
LIMIT Range high limit for thermocouple
RTD and mV inputs From the high limit of the selected input type to the
‘Low Range Limit’ parameter minus one display unit. Conf
L3 R/O
RNG.LO RANGE LOW
LIMIT Range low limit for thermocouple
RTD and mV inputs From the low limit of the selected input type to the
‘High Range Limit’ parameter minus one display unit. Conf
L3 R/O
PV.OFS PV OFFSET A simple offset applied to all input
values. Generally one decimal point more than PV L3
F I L T . T FILTER TIME Input filter time OFF to 100.0 seconds 1.6 L3
Auto Automatic
0 o C Fixed at 0 o C
C J . t y p CJC TYPE Configuration of the CJC type
50 o C Fixed at 50 o C
Auto Conf and if
T/C
L3 R/O
oFF No sensor break will be detected
on Open circuit sensor will be detected
S B . t y p SENSOR BREAK
TYPE Defines the action which is applied
to the control output if the sensor
breaks (open circuit).
Lat Latching
on Conf
L3 R/O
C J C . i n CJC
TEMPERATURE Temperature measured at the rear
terminal block. Used in the CJC
calculation Read only Conf
L3 R/O and
if T/C
P v . i n PV INPUT
VALUE Current measured temperature Minimum display to maximum display range Conf
L3 R/O
m v . i n MILLIVOLT
INPUT VALUE Millivolts measured at the rear PV
Input terminals xx.xx mV - read only Conf
L3 R/O
INPUT/OUTPUT LIST 1 ‘I O -1 ’
Name Scrolling Display Parameter Description Value Default Access Level
none No input or output fitted
dC.OP DC output
ReLy Relay output
L.IO Logic Input/Output
1..i d I/O 1 TYPE I/O channel 1 hardware type
defined by the hardware
fitted
SSR Triac output
As
ordered Read only
none Disabled. If disabled no further
parameters are shown
d.out Digital output
UP Valve open codes VC and VP only
dwn Valve close codes VC and VP only
Heat Heat output
CooL Cool output
d.in Digital input if ‘1.i d ’ = ‘ L.IO
HEAt Conf
w.SP Working setpoint re-transmission
PV Process variable re-transmission
1.FUNC I/O 1 FUNCTION I/O channel function.
If the instrument is ordered
as valve positioner (codes
VC or VP), only options
available are ,
none,
d.out, UP, or dwn
Note: If output 1 is set to
Up ensure the other valve
position output is set to
dwn and vice versa
OP Output power demand re-transmission
Shown if I/O 1 TYPE =
dc.OP Retransmission