Fitting the remote control lever (rcl²), Fitting.the.remote.control, Lever.(rcl²) – MAGURA TS6 User Manual
Page 18: Rcl²)
18
THE PASSION PEOPLE
www.magura.com
f
itting
the
remOte
COntrOl
lever
(rCl²)
L
L
You.will.notice.that.DLO².is.suitable.for.remote.control.because.the.blue.
dial.is.returned.to.its.original.position.by.a.return.spring.if.turned.by.hand..
Blue.dials.that.do.not.have.a.return.spring.do.not.support.remote.control.
with.RCL²!.However,.retrofitting.is.possible.at.a.MAGURA.service.centre..
DLO³.is.not.suitable.for.remote.control!
Danger of accident due to faulty installation work.
Î
–
Make.sure.that.the.RCL².cannot.interfere.with.brake.and.gear.shift.
actuation.and.function.in.any.lever.position.
Damage to material due to faulty installation work.
Î
–
Never.fit.the.clamps.in.the.wider.area.of.the.handlebar.
Î
–
Never.exceed.the.maximum.tightening.torques.
There.are.3.different.fastening.options.for.the.RCL².
Î
–
Standard.clamp.
.–.for.fitting.next.to.the.brake.lever.
Î
–
Standard.clamp.with.spacer.
.–.for.fitting.
next.to.the.brake.lever.in.combination.with.twist.shifters.
Î
–
Remote.mix.clamp.
.–.only.for.direct.fitting.to.brake.levers.of.MAGURA.
MT.Series.and.HS.Series.(MAGURA.rim.brakes).as.of.model.year.2011.
L
L
RCL².for.DLO².is.generally.mounted.on.the.right.
.–.however,.it.can.
be.mounted.on.the.left.side.if.required.
.
)
Define.the.position.of.the.standard.clamp.on.the.handlebar.
О
О
Make.sure.that.the.brake.and.gear.shift.actuation.and.function.is.not.
impaired.in.any.RCL².lever.position.
О
О
The.lever.
.and.return.dial.
.on.the.RCL².must.be.easily.reachable.
.
)
Tighten.the.clamping.screw.
.on.the.standard.clamp.with.a.tighten-
ing.torque.of.
max. 3 N·m (27 lbf·in).
.
)
Tighten.the.sleeve.nuts.
.on.the.Remote.Mix.clamp.with.a.tightening.
torque.of.
max. 3 N·m (27 lbf·in).
Fitting the RCL² Bowden cable
Danger of accident due to faulty installation work.
Î
–
Make.sure.that.the.Bowden.cables.on.the.RCL².can.never.interfere.with.
steering.
О
О
The.outer.sleeve.must.be.laid.via.the.shortest.route,.without.torsion.or.
kinking,.between.the.stops.
.on.the.RCL².and.the.fork.crown.
.
)
Shorten.the.outer.sleeve.of.the.Bowden.cable.with.suitable.Bowden.
cable.pliers.
.
)
Make.sure.that.the.lever.on.the.RCL².is.relieved.–.press.the.return.dial.
if.necessary..
.
)
Feed.the.inner.cable.through.the.RCL²,.outer.sleeve.and.stop.on.the.
fork.crown.
.
)
Make.sure.that.the.outer.sleeve.is.firmly.seated.in.the.stops.
Fit.the.inner.DLO².cable.
:
.
)
Remove.the.cover.on.the.“DLO²”.by.unscrewing.counter-clockwise.
.
)
Loosen.the.clamping.screw.
.by.2–3.turns.
.
)
Tension.the.inner.cable.and.insert.it.into.the.groove.on.the.rotating.dial.
and.under.the.washer.on.the.clamping.screw.and.hold.in.place.
.
)
Tighten.the.clamping.screw.with.a.tightening.torque.of.
max. 2 N·m
(18 lbf·in).
.
)
Trim.the.inner.cable.to.a.length.of.approx.2.cm.after.the.clamping.
screw.
.
)
Push.the.end.of.the.inner.cable.through.the.cutout.into.the.inside.of.the.
rotating.dial.
.
)
Replace.the.cover.on.the.“DLO²”.by.screwing.it.on.clockwise.
.
)
Retension.the.inner.cable.after.the.first.10–20.actuations.