Anthro Fit Adjusta Unit 60 Assembly Instructions - Manual (Page 2)

Anthro Corporation Technology Furniture ® 10450 SW Manhasset Drive Tualatin, Oregon 97062 1-800-325-3841 anthro.com
01– 60" Wide Fixed Worksurface ..Qty. 1 ...................100-6457-00
02– 60" Wide Caddy Worksurface .Qty. 1 ...................100-6461-00
03– 60" Wide Adjusta Mechanism ......Qty. 1 ...................225-5548-00
(The Adjusta Mechanism is packaged separately & requires assembly)
04– Small Support Bracket X ............Qty. 1 ...................225-2014-00
05– 24.875" Adjusta Vertical Legs ........Qty. 4 ...................125-5230-00
06– Adjusta Base Tubes ......................Qty. 2 ..................125-5276-00
07– Cross Tubes ....................................Qty. 2 ...................125-5221-00
08– Insert Screws .................................Qty. 4 ...................325-5052-00
09– 2.0" Large End Caps ...................Qty. 4 ...................175-5157-00
10– Caster Inserts ...............................Qty. 4 ...................525-5032-00
11– 3" Locking Casters ......................Qty. 2 ...................150-5053-00
12–
5 /
16
-18 Bolts ....................................Qty. 8 ...................325-5194-00
13– Tube Washers ................................Qty. 8 .. 225-2050-00 or 225-3522-00
14– 3" Non-Locking Casters ...........Qty. 2 ...................150-5052-00
15–
1 /
4
-20 Button Head Screws .......Qty. 8 ...................325-5003-00
16– Cross Ends .....................................Qty. 2 ...................225-5334-00
17–
1 /
4
-20 Keps Nuts ...........................Qty. 4 ...................325-5130-03
18– 3 /
4
" Wood Screws .........................Qty. 42 ................325-5106-00
19– Support Screws ............................Qty. 12 ................325-5010-00
20– Small Support Bracket Y ...........Qty. 1 ...................225-2015-00
21– 60" Wide Buttress ......................Qty. 2 ...................225-5549-00
22– 60" Wide Back Trough ..............Qty. 1 ...................225-2293-00
23– 1.5" Small Caps .............................Qty. 4 ...................175-5156-00
All Fastener quantities listed here are the minimum needed
for your Adjusta Unit assembly. There may be a few extra
Fasteners included, which are not counted in the Parts List.
Component list for part #’ FAJ60zz/xx3
NOTE: Detailed views of all Hardware are provided with each Assembly Step.
05
07
08
03
02
10
12
06
01
09
13
14
16 17
18
21
11
04
19
20
15
22
23
Step 12
(requires Worksurface to be 12" from floor)
Rotate the Caddy Worksurface so the predrilled holes
face upward.
Slide the Caddy under the Mechanism and align the three
holes located on each end of the Caddy and Mechanism.
Secure the Caddy using a total of six Wood Screws. Then,
secure the Paddle to the Caddy using four Wood Screws.
NOTE: Make certain the Cable for the Paddle is positioned
underneath the Adjusta Bar.
3 /
4
" Wood Screw
325-5106-00
Paddle
Adjusta Bar
(12" high surface shown shaded)
Cable
Wood Screw
Step 13
Install two Caster Inserts into each Base Tube and
secure with one Insert Screw per Insert.
Insert one Locking and one Non-Locking Caster into
each Insert of a Base Tube as shown.
Insert two End Caps into the ends of each Base Tube.
Insert Screw
(with pink threads)
325-5052-00
Locking
Caster
Caster Inserts placed
into the large holes
Leave these two side holes open
Non-Locking
Caster
Step 14
Attach a Cross Tube to a Base Tube by inserting a Bolt
through a Tube Washer, then insert the Bolt through the
Base Tube and carefully thread into the Cross Tube.
Repeat this procedure for other Cross Tube.
Then tighten all Bolts.
Tube Washer
225-2050-00 or 225-3522-00
Cross Tube
Tube Washer
( 5 /
16
-18 X 3.5") Bolt
325-5194-00
Bolt
Base Assembly