Anthro MiniCart Assembly Instructions - Manual

TECHNOLOGY FURNITURE ®
300-5385-00
*300-5385-00*
Anthro MiniCart
Assembly Instructions
01 – Insert Screws ............................ Qty. 4 ................. 325-5052-00
02– 2
3 /
8
" Non-Locking Casters ........ Qty. 2 ............... 150-5002-03*
03– Caster Inserts ........................... Qty. 4 ............... 525-1000-00*
04– 2
3 /
8
" Locking Casters ................ Qty. 2 ............... 150-5003-03*
05– 1.75" Large End Caps ............ Qty. 2 .................. 175-5021-xx
06– Base Tube Screws ..................... Qty. 3 ................. 325-5000-00
07– MiniCart Base Tube ..................... Qty. 1 .................. 125-5004-xx
08– Support Screws ........................ Qty. 6 ................. 325-5010-00
09– Vertical Legs .............................. Qty. 3 .................. 125-5020-xx
10– Clamp Screws ........................... Qty. 6 ................. 325-5086-00
11– Shelf Supports .......................... Qty. 6 .................. 175-5060-xx
12– Shelf Clamps ............................. Qty. 6 .................. 175-5059-xx
Enclosed Parts List
Detailed views of all Hardware is provided with each Assembly Step 13– MiniCart Shelves ...................... Qty. 2 .................. 100-6003-xx
14– 1.5" Small End Caps ............... Qty. 3 .................. 175-5020-xx
All Fastener quantities listed here are the minimum needed
for your Cart assembly. There may be a few extra
Fasteners included, which are not counted in the Parts List.
To make the assembly of your Anthro MiniCart even easier, we have included
all of the required tools (not shown above). The handy Hex Driver Bit can be
used in your electric drill in place of the Hex Driver.
Hex Driver 5 /
32
" ........................ Qty. 1 ................. 375-5000-00
Hex Driver Bit 5 /
32
" .................. Qty. 1 ................. 375-5003-00
8 oz. Rubber Mallet .................. Qty. 1 ................. 375-5022-00
Anthro Corporation Technology Furniture ® 10450 SW Manhasset Drive Tualatin, Oregon 97062
SAVE THESE INSTRUCTIONS! Document # 300-5068-00
Step 7
Install all four Caster Inserts into the Base Tube and
secure (fully tighten) with one Insert Screw per Insert.
Next, push the Casters, (locking ones in front) into the
Caster Inserts.
Step 8
Carefully rotate the Shelf Assembly (from Step 6),
upside down as shown.
Place the Base Tube Assembly (from Step 7) onto the
Vertical Legs of the Shelf Assembly.
Attach the Base Tube to each Leg using a total of three
Base Tube Screws.
Tighten all Support and Base Tube Screws.
Step 9
Rotate your MiniCart over onto the Casters.
Pop the three 1.5" Small End Caps into the Vertical Legs
and the two 1.75" Large End Caps into the Base Tube.
Congratulations! Your MiniCart assembly is complete.
Please return the enclosed Registration Card to receive
our product updates, new catalogs, and sale flyers.
Thank you for choosing Anthro!
March 2006
These Assembly Instructions are
for the GT23xx.
Before beginning assembly of your
Anthro MiniCart, please take a moment
to review the parts listed below to verify
that your shipment is complete.
✔
Does your Cart have 4" Casters?*
(Such as a GT23xx4. Your Caster Part
Numbers are given here.)
✔
Does your Cart have Glides?*
(Such as a GT23xxGL. Your Glide and Glide
Insert Part Numbers are given here.)
4" Locking Caster
150-5011-03
4" Non-Locking Caster
150-5010-03
Glide Insert
525-1004-00
Glide
325-5042-00
Questions? 1-800-325-3841
Insert Screw
(small pink patch on end)
325-5052-00
Base Tube Screw
325-5000-00
GLIDES ONLY
Thread each Glide
into the Glide Inserts
04 06
07
03
02
09
10
05
12
01
08
11
14
13
1.5" Small End Cap
1.75" Large End Cap
Locking Casters