Anthro Large AnthroCarts 60W Assembly Instructions - Manual

TECHNOLOGY FURNITURE ®
60” Wide AnthroCart
Assembly Instructions
01 – Insert Screws ............................ Qty. 6 ...................... 325-5052-00
02– 1.75” Large End Caps ............ Qty. 2 ....................... 175-5021-xx
03– Caster Inserts ........................... Qty. 6 ...................... 525-1000-00*
04– 2 3 /
8
” Locking Casters ................ Qty. 2 ...................... 150-5003-03*
05– 2 3 /
8
” Non-Locking Castors ....... Qty. 4 ...................... 150-5002-03*
06– Base Tube Screws ..................... Qty. 4 ......................... 325-5000-00
07– 60” Wide Base Tube ................ Qty. 1 ............................. (see below)
30” Deep Base Tube (H24xx) ......................................... 125-5177-xx
36” Deep Base Tube (H25xx) ......................................... 125-5178-xx
08– 23.875” Vertical Legs .............. Qty. 4 ......................... 125-5020-xx
09– 3 /
4
” Wood Screws .................... Qty. 21 ...................... 325-5106-00
10– 56” Handle Lip ......................... Qty. 1 ......................... 225-5347-xx
11– Support Screws ........................ Qty. 16 ...................... 325-5010-00
12– 58” Wide Bridge Pan .............. Qty. 1 ......................... 225-5341-xx
Enclosed Parts List
Detailed views of all Hardware are provided with each Assembly Step.
13– Bracket Screws .......................... Qty. 4 ......................... 325-5149-00
14– 4.75” Pan End Bracket ........... Qty. 2 ......................... 225-5344-xx
15– Clamp Screws ........................... Qty. 4 ......................... 325-5086-00
16– Shelf Supports .......................... Qty. 4 ......................... 175-5060-xx
17– Shelf Clamps ............................. Qty. 4 ......................... 175-5059-xx
18– 60” Wide Shelf ......................... Qty. 1 ............................. (see below)
30” Deep Shelf (H24xx) .................................................. 100-6337-xx
36” Deep Shelf (H25xx) .................................................. 100-6338-xx
19– 1.5” Small End Caps ............... Qty. 4 ......................... 175-5020-xx
20– 18” Bridge Side Gussets ........ Qty. 2 ......................... 225-5337-xx
All Fastener quantities listed here are the minimum needed
for your Cart assembly. There may be a few extra
Fasteners included, which are not counted in the Parts List.
Anthro ® Corporation Technology Furniture ® 10450 SW Manhasset Drive Tualatin, Oregon 97062
SAVE THESE INSTRUCTIONS! anthro.com
Step 8
Install all six Caster Inserts into the Base Tube and
secure with one Caster Screw per Insert.
Push the Casters, (locking ones in front) into the
Caster Inserts.
Step 9
Place the Base Tube Assembly (from Step 8) onto the
Vertical Legs of the Shelf Assembly (from Step 7).
Attach the Base Tube to the Legs using a total of four
Base Tube Screws.
TIGHTEN ALL SCREWS.
Step 10
Carefully, rotate your Cart over onto the Casters.
Pop the 1.5” Small End Caps into the Vertical Legs and
the 1.75” Large End Caps into the Base Tube.
Congratulations! Your assembly is complete.
Please return the enclosed Registration Card to receive
our product updates, new catalogs, and sale flyers.
Thank you for choosing Anthro!
October 2002 Rev. B
These Assembly Instructions are
for the H24xx & H25xx.
Before beginning assembly of your 60”
Wide AnthroCart, please take a moment
to review the parts listed below to verify
that your shipment is complete.
✔
Does your Cart have 4” Casters?*
(Such as an H24xx4. Your Caster Part
Numbers are given here.)
✔
Does your Cart have Glides?*
(Such as an H24xxGL. Your Glide and Glide
Insert Part Numbers are given here.)
4” Locking Caster
150-5011-03
4” Non-Locking Caster
150-5010-03
Glide Insert
525-1004-00
Glide
325-5042-00
04
06
07
03
02
09
12
05
01
08
13
Base Tube Screw
325-5000-00
Insert Screw
(small pink patch on end)
325-5052-00
To make the assembly of your 60” Wide
AnthroCart
even easier, we have included
all of the required tools. The handy Hex
Driver Bit can be used in your electric
drill in place of the Hex Driver.
Hex Driver 5 /
32
" ........... 375-5000-00
Hex Driver Bit 5 /
32
" .... 375-5003-00
8 oz. Rubber Mallet ..... 375-5022-00
Questions? 1-800-325-3841
14
15
16
17
19
20
11
1.5” Small End Cap
1.75” Large End Cap
18
Locking Casters
10
GLIDES ONLY
Thread each Glide
into the Glide Inserts