Anthro UltraCompact Cart Assembly Instructions - Manual

TECHNOLOGY FURNITURE ®
UltraCompact Cart
Assembly Instructions
01– Caddy Tray ................................. Qty. 1 ................. 225-5046-00
02– Rubber Bumpers ..................... Qty. 2 ................. 175-5130-03
03– Caddy Screws ........................... Qty. 4 ................. 575-5001-10
04– Keyboard Pads .......................... Qty. 4 ................. 575-5001-11
05– Wrist Rest ................................ Qty. 1 ................. 575-5001-01
06– Caddy Platform ........................ Qty. 1 ................. 575-5001-04
07– Acorn Nuts ............................... Qty. 4 ................. 325-5023-00
08– Caddy Mechanism ................... Qty. 1 ................. 575-5001-09
09– Mouse Pad ................................. Qty. 1 ................. 575-5001-03
10– Mouse Rail ................................. Qty. 1 ................. 575-5001-02
11–
3 /
4
” Wood Screws .................... Qty. 10 ............... 325-5106-00
12– 1.75” Large End Caps ............. Qty. 2 .................. 175-5021-xx
13– 2
3 /
8
” Locking Casters ............ Qty. 2 .............. 150-5003-00*
14– Base Tube Screws .................... Qty. 4 ................. 325-5000-00
15– Caster Inserts ........................... Qty. 4 ............... 525-1000-00*
16– Insert Screws ............................ Qty. 4 ................. 325-5052-00
17– 2 3 /
8
” Non-Locking Casters ... Qty. 2 .............. 150-5002-00*
18– Vertical Legs .............................. Qty. 4 .................. 125-5049-xx
19– 1.5” Small End Caps ............... Qty. 4 .................. 175-5020-xx
20– Clamp Screws ........................... Qty. 8 ................. 325-5086-03
21– Shelf Supports .......................... Qty. 8 .................. 175-5060-xx
22– Shelf Clamps ............................. Qty. 8 .................. 175-5059-xx
23– Support Screws ........................ Qty. 8 ................. 325-5010-00
24– Ultra Compact Large Shelf .... Qty. 1 .................. 100-6001-xx
25– Ultra Compact Small Shelf .... Qty. 1 .................. 100-6005-xx
26– Ultra Compact Base Tube ...... Qty. 1 .................. 125-5046-xx
All Screw quantities listed here are the minimum needed
for your Cart assembly. There may be a few extra Screws
included, which are not counted in the Parts List.
The following Tools (not shown) have been included with your Cart.
Hex Driver 5 /
32
" ......................... Qty. 1 ................. 375-5000-00
Hex Driver Bit 5 /
32
" ................... Qty. 1 ................. 375-5003-00
Anthro ® Corporation Technology Furniture ® 10450 SW Manhasset Drive Tualatin, Oregon 97062 anthro.com
SAVE THESE INSTRUCTIONS! Rev. B June 2003
Step 8
Install all four Caster Inserts into the Base Tube and
secure with one Insert Screw per Insert. Push the
Casters, (locking ones in front) into the Caster Inserts.
Next, place the Base Tube Assembly onto the Vertical Legs
of the Shelf Assembly. Attach the Base Tube to each Leg
using a total of four Base Tube Screws.
Step 9
Unpack the remaining Keyboard & Mouse Caddy items.
First, slide the Caddy Mechanism into the installed Tray
and push to the rear.
NOTE: If needed, rotate the Mechanism Handle and LIFT to
allow the Mechanism to slide to the rear.
Second, install the remaining Wood Screw and Rubber
Bumper into the front of the Tray.
1-800-325-3841
Hello! Thank you for choosing Anthro.
Before beginning assembly of your
UltraCompact Cart, please take a
moment to review the parts listed below
to verify that your shipment is complete.
It may be helpful to review the
assembly instructions of all Anthro
products you purchased and are
planning to include in this installation.
A Philips Head Screwdriver & Adjust-
able Crescent Wrench (not included)
will be required for this assembly.
4 Does your Cart have 4” Casters?*
(Such as a 075xx4. Your Caster Part Num-
bers are given here.)
4 Does your Cart have Glides?*
(Such as a 075xxGL. Your Glide and Glide
Insert Part Numbers are given here.)
4” Locking Caster
150-5011-00
4” Non-Locking Caster
150-5010-00
Glide Insert
525-1004-00
Glide
325-5042-00
Base Tube Screw
325-5000-00
Questions? 1-800-325-3841
12
13
15
16
18
14
19
17
23
21
22
20
26
24
25
Insert Screw
(small pink patch on end)
325-5052-00
3 / 4 ” Wood Screw
325-5106-00
GLIDES ONLY
Thread each Glide
into the Glide Inserts
Locking
Casters
Rubber Bumper
NOTE: The Rubber Bumper is located
towards the rear of the Cart
05
04
02
06
01
ITEMS 01-11
ARE BOXED SEPARATELY
FROM YOUR CART
03
08
07
10
09
11
Component list for part #
075xx , 075Lxx
Caddy Mechanism
Rubber Bumper
Rear
of
Cart
Wood Screw
Rotate Handle
to LIFT
(#10-24) Acorn Nut
325-5023-00
Step 10
(requires the Crescent Wrench & Screwdriver)
Carefully rotate your Cart back onto the Casters.
Pull the Mechanism to the front and place the Platform
onto the Mechanism. Secure the Platform using the four
Caddy Screws and Acorn Nuts.
Then, place the Mouse Rail, Pad & Wrist Rest onto the
Platform as best suits your personal preference.
Pop the Small End Caps into the Legs and the Large End
Caps into the Base Tube. Congratulations! Your assembly
is complete.
(#10-24) Caddy Screw
575-5001-10
Caddy Screws
Acorn
Nuts
Platform
Mouse
Pad
KB Pads
Wrist Rest
Mouse Rail
Adjust the Platform height & angle:
1. Rotate the Handle counterclockwise.
2. Reposition the Shelf, then retighten the Handle.
Adjust the Platform rotation:
1. Firmly grasp the Platform, then rotate to the desired angle.
Adjusting your Keyboard & Mouse Caddy
2
1
Rotate