Yokogawa EJX430B - Manual (Page 95)

<11. General Specifications>
11-4
IM 01C27B01-01EN
11.2 Model and Suffix Codes
Model EJX110B
Model Suffix Codes Description
EJX110B . . . . . . . . . . . . . . . . . . . . . . Differential pressure transmitter
Output signal -L . . . . . . . . . . . . . . . . . . . . Wireless communication (ISA100.11a protocol)
Measurement
span (capsule)
F . . . . . . . . . . . . . . . . . . .
L . . . . . . . . . . . . . . . . . . .
M . . . . . . . . . . . . . . . . . .
H. . . . . . . . . . . . . . . . . . .
V. . . . . . . . . . . . . . . . . . .
0.1 to 5 kPa (0.4 to 20 inH
2
O) (For wetted parts material code S)
0.1 to 10 kPa (0.4 to 40 inH
2
O) (For wetted parts material code M, H, T, A,
D and B)
0.5 to 100 kPa (2 to 400 inH
2
O)
2.5 to 500 kPa (10 to 2000 inH
2
O)
0.07 to 14 MPa (10 to 2000 psi)
Wetted parts
material *1
 . . . . . . . . . . . . . . . . . Refer to “Wetted Parts Materials” Table 1.
Process connections
►
0 . . . . . . . . . . . . . . . .
1 . . . . . . . . . . . . . . . .
2 . . . . . . . . . . . . . . . .
3 . . . . . . . . . . . . . . . .
4 . . . . . . . . . . . . . . . .
5 . . . . . . . . . . . . . . . .
without process connector (Rc1/4 female on the cover flanges)
with Rc1/4 female process connector
with Rc1/2 female process connector
with 1/4 NPT female process connector
with 1/2 NPT female process connector
without process connector (1/4 NPT female on the cover flanges)
Bolts and nuts material J . . . . . . . . . . . . . .
G. . . . . . . . . . . . . .
C. . . . . . . . . . . . . .
ASTM-B7 carbon steel
316L SST stainless steel
ASTM grade 660 stainless steel
Installation
►
-7 . . . . . . . . . . .
-8 . . . . . . . . . . .
-9 . . . . . . . . . . .
-B . . . . . . . . . . .
-U . . . . . . . . . . .
Vertical piping, left side high pressure, and process connection downside
Horizontal piping and right side high pressure
Horizontal piping and left side high pressure
Bottom Process Connection, left side high pressure *2
Universal flange *2
Amplifier housing 7 . . . . . . . . . .
8 . . . . . . . . . .
9 . . . . . . . . . .
Cast aluminum alloy with integral antenna
Cast aluminum alloy with detachable antenna (2 dBi) *4
Cast aluminum alloy without antenna (N connector) *3*4
Electrical connection J . . . . . . . . . No electrical connection, battery-powered type (battery case only; battery
cells not included)
Integral indicator ► D. . . . . . . Digital indicator
Mounting bracket ► B. . . . .
D. . . . .
G. . . . .
K. . . . .
M . . . .
N. . . . .
304 SST 2-inch pipe mounting, flat type (for horizontal piping)
304 SST 2-inch pipe mounting, L type (for vertical piping)
304 SST 2-inch pipe mounting (for bottom process connection type)
316 SST 2-inch pipe mounting, L type (for vertical piping)
316 SST 2-inch pipe mounting (for bottom process connection type)
None
Optional codes /  Optional specification
The “►” marks indicate the most typical selection for each specification.
*1: ! Users must consider the characteristics of selected wetted parts material and the influence of process fluids. The use of
inappropriate materials can result in the leakage of corrosive process fluids and cause injury to personnel and/or damage to plant
facilities. It is also possible that the diaphragm itself can be damaged and that material from the broken diaphragm and the fill fluid
can contaminate the user’s process fluids.
Be very careful with highly corrosive process fluids such as hydrochloric acid, sulfuric acid, hydrogen sulfide, sodium hypochlorite,
and high-temperature steam (150°C [302°F] or above). Contact Yokogawa for detailed information of the wetted parts material.
*2: Applicable for wetted parts material code S.
*3: Order the antenna separately from accessary option.
*4: Remote antenna cables can be attached. Order separately from accessary option.