Yokogawa EJA530A - Manual (Page 35)

IM 01C21F01-01E 8-4
8. BRAIN TERMINAL BT200 OPERATION
8.3 Setting Parameters Using the BT200
8.3.1 Parameter Summary
Instruments to which applicable:
F: Differential pressure transmitters
EJA110A, EJA120A, and EJA130A
P: Pressure transmitters EJA310A, EJA430A, EJA440A, EJA510A, and EJA530A
L: Liquid level transmitters EJA210A and EJA220A
No. Description
Model+capsule type
Tag number
Applica-
bility
P L F
01
02
T0805.EPS
Rewrita-
bility
16 alphanumerics
GOOD/ERROR
Remarks Item
MODEL
TAG NO.
Self-diagnostic result
—
—
—
03 SELF CHECK
Measured data display A
–5 to 110%* 3
Menu name DISPLAY
Output (in %) A10 OUTPUT (%)
–19999 to 19999 Output (in engineering
units) A11 ENGR.
OUTPUT
Unit specified in D30 Amplifier temperature A20 AMP TEMP
Unit specified in D30 Capsule temperature A21 CAPSULE
TEMP
—
Sensor type B
16 uppercase alphanumerics
Menu name SENSOR
TYPE
Model+span B10 MODEL
—
Style number B11 STYLE NO.
–32000 to 32000 Lower range-limit B20 LRL
–32000 to 32000 Upper range-limit B21 URL
–32000 to 32000 Minimum span B30 MIN SPAN
—
—
—
—
—
Unit specified in D31* 1 Static pressure A30 STATIC
PRESS
–32000 to 32000 Input (indicated as the
value after zeroing) A40 INPUT
GOOD/ERROR, CAP MODULE FAULT, AMP MODULE FAULT,
OUT OF RANGE, OUT OF SP RANGE*
1 , OVER TEMP (CAP),
OVER TEMP (AMP), OVER OUTPUT, OVER DISPLAY,
ILLEGAL LRV, ILLEGAL HRV, ILLEGAL SPAN, and
ZERO ADJ OVER
Self-diagnostic
messages A60 SELF CHECK
—
—
—
—
—
—
—
Maximum static
pressure*
6
B40
Same as A60
MAX STAT.P.
Self-diagnostic
messages
—
—
B60 SELF CHECK
Setting data C
16 alphanumerics
Menu name SETTING
Tag number C10 TAG. NO.
Selected from mmH
2
O, mmAq,
mmWG, mmHg, Torr, Pa, hPa, kPa,
MPa, mbar, bar, gf/cm
2 , kgf/cm 2 ,
inH
2
O, inHg, ftH
2
O, psi, or atm
Measurement range
units C20 PRESS UNIT
–32000 to 32000(but within
measurement range) Measurement range,
lower range value C21 LOW RANGE
—
Self-diagnostic
messages C60 Same as A60 SELF CHECK
—
—
—
—
–32000 to 32000(but within
measurement range) Measurement range,
higher range value C22 HIGH
RANGE
Selected from 0.2* 2 , 0.5, 1.0, 2.0,
4.0, 8.0, 16.0, 32.0, or 64.0 sec.
Damping time constant C30 AMP
DAMPING
Selected from OUT:LIN; DSP:LIN,
OUT:LIN; DSP:SQR,
OUT:SQR; DSP:SQR Output mode and
integral indicator mode C40 OUTPUT
MODE
0.0 to 20.0%
LINEAR/ZERO Low cut D10 LOW CUT
Low cut mode D11 LOW CUT
MODE
NORMAL %/USER SET,
USER & %/INP PRES, PRES & % Display selection D20 DISP SELECT
—
Auxiliary setting data 1 D Menu name AUX SET 1
—
Default Value
As specified when ordered.
As specified when ordered.
As specified when ordered.
As specified when ordered.
2.0 s
As specified when ordered.
If not specified,
OUT: LIN; DSP: LIN.
8 uppercase
alphanumerics Engineering unit for
display D21 DISP UNIT
10.0%
LINEAR
–5.0 to 110.0% Lower output range-limit D15 OUT LIMIT(L) –5.0%* 1
–5.0 to 110.0% Upper output range-limit D16 OUT LIMIT(H) 110.0%
–19999 to 19999 Engineering range,
lower range value D22 DISP LRV
–19999 to 19999 Engineering range,
higher range value D23 DISP HRV
As specified when ordered.
As specified when ordered.
As specified when ordered.
deg C/deg F Temperature setting
units D30 TEMP UNIT deg C
*1: Unless otherwise specified by order. When optional code /F1 is specified, substitute the value –5 with –2.5.