Watlow Series 94 - Manual (Page 21)

W a t l o w S e r i e s 9 4 S e t u p ■ 4 . 5
Setup
Parameter Value Range Factory Default Appears If:
[`LOC] 0 - 3 0
[``In] [```J], [```H] (K) , [```t], [```n], [```S], [```J] DIP switch selectable.
[```b], [`rtd], [`r†d]
[`C_F] [```C] or [```F] [```F] [`LOC] is set to [```0]
[``rL] [``rL] to [``rh] Input dependent. [`LOC] is set to [```0]
[``rh] ``rh] to [``rL] Input dependent. [`LOC] is set to [```0]
[`Ot1] [``HI], [``LO], [`H_L] [`H_L] [`LOC] is set to [```0]
[`HSL] 1 - 9999, 0.1 - 999.9°F 3, 0.3°F [`LOC] is set to [```0]
1 to 5555, 0.1 to 555.5°C 2, 0.2°C
[`Ot2] [`PrA] = Process Alarm [``no] [`LOC] is set to [```0]
[``Pr] = Process with no alarm message
[``no] = None
[`HSA] 1 - 9999, 0.1 - 999.9°F 3, 0.3°F [`Ot2] is set to [``Pr] or [`PrA] and
1 - 5555, 0.1 - 555.5°C 2, 0.2°C [`LOC] is set to [```0]
[`LAt] [`LAt] or [`nLA] [`nLA] [`Ot2] is set to [``Pr] or [`PrA] and
[`LOC] is set to [```0]
[`SIL] [``On] or [`OFF] [`OFF] [`Ot2] is set to [``Pr] or [`PrA] and
[`LOC] is set to [```0]
[`rtd] [`JIS] or [`din] [`din] [``In] is set to [`rtd] or [`r†d] and
[`LOC] is set to [```0]
[``UP] [``no] = no display shown [`Pro] [`LOC] is set to [```0]
[`Pro] = Process
[`LoL] = Low limit set point
[`HiL] = High limit set point
[`LoA] = Alarm low set point
[`HiA] = Alarm high set point
[`bot] [``no] = no display shown [`HiL] [`LOC] is set to [```0]
[`Pro] = Process
[`LoL] = Low limit set point
[`HiL] = High limit set point
[`LoA] = Alarm low set point
[`HiA] = Alarm high set point
Input Type Sensor Range Low Sensor Range High
[```J] 32°F/0°C 1382°F/750°C
[```H] (K) -328°F/-200°C 2282°F/1250°C
[```t] -328°F/-200°C 662°F/350°C
[```n] 32°F/0°C 2282°F/1250°C
[```S] 32°F/0°C 2642°F/1450°C
[```b] 32°F/0°C 3308°F/1820°C
[`rtd] (1°) -328°F/-200°C 1292°F/700°C
[`r†d] (0.1°) -199.9°F/-199.9°C 999.9°F/700.0°C
Table 4.5a -
Input Ranges.
Table 4.5b -
Setup Menu Prompts
and Descriptions.
Setup Menu
NOTE:
Document your setup menu parameters.
Do not enter any values here; make photocopies instead.