beautypg.com

Trouble shooting – Bosch TDS4530 User Manual

Page 21

background image

21

BOSCH

ENGLISH

Trouble shooting

Problem

Possible causes

Solution

Pilot light (11)

flashes

• Boiler and filter must be rinsed.

• Rinse the filter and the boiler according

to the cleaning instructions in this

manual (see section E).

The steam generator

does not come on.

• There is a connection problem.

• The main power button is not

switched on.

• Check the mains cable (6), the plug

and the socket.

• Set the main power button (12) to the

“I” position (illuminated in red).

The iron does not

heat up.

• The main power button is not

switched on.

• The temperature is set to a low

position.

• Set the main power button (12) to the

“I” position (illuminated in red).

• Set the temperature to the desired

position.

The iron begins to

smoke when

switched on.

• During first use: certain

components on the appliance

have been lightly greased at the

factory and may produce a little

smoke when initially heated.

• During subsequent use: the

soleplate may be soiled.

• This is completely normal and will stop

after a short while.

• Clean the soleplate according to the

cleaning instructions in this manual.

Water flows through

the holes on the

soleplate.

• The steam function is being used

before it has reached the correct

temperature.

• The water is condensing inside

the pipes because steam is being

used for the first time or has not

been used for a long time.

• The steam generator contains too

much scale.

• Reduce the steam flow when ironing at

low temperatures.

• Point the iron away from the ironing

area and press the steam release

button until steam is produced.

• Clean the boiler as described in

section “Calc'n'Clean Advanced” (E).

Dirt comes out

through the

soleplate.

• There is a build up of scale or

minerals in the steam tank.

• Chemical products or additives

have been used.

• Use tap water mixed 50% with distilled

or demineralised water. To prolong the

optimum steam function, mix tap water

with distilled water 1:1. If the tap water

in your district is very hard, mix tap

water with distilled water 1:2.

• Clean the soleplate with a damp cloth.

• Never add products to the water.

The iron does not

produce any steam.

• The boiler is not switched on or

the water tank is empty.

• The steam regulation is set to the

minimum position.

• Set the main power button (12) to the

“I” position (illuminated in red), and/or

fill the water tank.

• Increase the steam flow (see section

B).

The ironed garment

turns dark and/or

sticks to the

soleplate.

• The selected temperature is too

high and has damaged the

garment.

• Select a suitable temperature for the

material being ironed and clean the

soleplate with a damp cloth.

The soleplate turns

brown.

• This is a regular consequence of

continued use over a long period

of time.

• Clean the soleplate with a damp cloth.

Problem

Possible causes

Solution

The appliance

makes a pumping

sound.

• Water is being pumped into the

steam tank.

• Water tank (1) is not correctly

inserted in the housing.

• The sound will not stop.

• This is normal.

• Adjust the water tank to fit correctly.

• If the sound will not stop, do not use

the steam generator and contact an

authorised technical service centre.

Loss of pressure

during ironing.

• Steam release button has been

activated for too long a period of

time, that is, it has been pressed

too frequently.

• Use the steam release button at

intervals. This improves the ironing

result as the textiles will be steamed,

dried and ironed properly.

Water spots appear

on the garment

during ironing.

• May be caused by steam

condensed on the ironing board.

• Wipe the textile cover of the ironing

board, and iron any water drops to dry

them.

Water spots appear

on the garment

during use of the

“PulseSteam”

function.

• Water spots are caused by steam

condensation in the hose when

cooling down after use.

• Water drops stop coming out of the

soleplate after using the “PulseSteam”

function for some time.

The hose gets hot

during use.

• This is normal. It is caused by the

steam passing through the hose

during steam ironing.

• Place the hose on the opposite side so

that you cannot touch the hose during

ironing.

Water leakage from

the boiler.

• Filter (4) located at the side of the

appliance is loose.

• Tighten up the filter.

The iron does not

stop steaming after

placing it on the pad

(2).

• “PulseSteam” function has been

activated by double click.

• Just press the trigger once again and

the iron will stop steaming at once.

If the above does not solve the problem, get in touch with an authorised technical service.

You can download this manual from the local homepages of Bosch.