FIREPOWER Firefinder XLS - Manual (Page 10)

s Industry, Inc.
Building Technologies Division
Remote System Enclosures
Models REMBOX2 and REMBOX4 are FireFinder XLS system
enclosures that are used for remotely mounting inner-
door modules like the Model PMI interface, switch mod-
ules, Model LVM live voice modules, and Model FMT
firefighters master telephone modules. Models
REMBOX2 and REMBOX4 are thinner than the regular CAB
series of enclosures – just 5" (12.7cm.) deep overall, and
are perfect for mounting in places where space is limited
(e.g. – office-complex lobbies or behind a receptionist's
desk). No card cages, power supplies or bulk amplifiers
can be mounted in a given REMBOX because of their
smaller depth. However, Model PMI and modules (e.g. –
the remote network interface module [Model RNI], the
output control module [Model OCM-16], and the
supervised input module [Model SIM-16]) can be mounted
in a given REMBOX.
Due to the depth of the live voice module and the
firefighters’ master telephone, no Model OCM-16 or Model
SIM-16 modules can be used simultaneously with Model
LVM or Model FMT. The REMBOX2 and the REMBOX4 are
designed for flush mounting with no trim kit required. Both
enclosures also come with a clear lens plate on the cover.
REMBOX2 Two Module Remote Enclosures
REMBOX2 Two Module Remote Enclosures
The REMBOX2 has two (2) inner-door module spaces, and
can hold a single Model PMI, up to two (2) switch module
brackets and one (1) Model LVM. Combinations are also
allowed.
The REMBOX2 can also mount a single RNI remote
network interface on a bracket included in the backbox. A
bracket called the REMBOX2-MP can be used to mount up
to four OCM-16 output control modules or SIM-16
supervised input modules. The REMBOX2-MP must be
purchased separately. Approximate size of the REMBOX2
is 14-1/2" (36.8cm.) wide, 18-1/2" (47cm.) high and 5"
(12.7cm.) deep.
REMBOX4 Four Module Remote Enclosures
REMBOX4 Four Module Remote Enclosures
The REMBOX4 has space for mounting four (4) inner-
door modules. Any combination of Model PMI (two-
module spaces), switch module brackets, Model LVM
or Model FMT (one-module space each) can be used.
Unused module spaces can be covered with Model ID-SP
blank plates. The REMBOX4 can also mount a single
remote network interface (Model RNI) on a bracket
included in the backbox. A bracket known as Model
REMBOX4-MP can be used to mount up to eight (8)
output control modules (Model OCM-16) or supervised
input modules (SIM-16). The REMBOX4-MP must be
purchased separately. Approximate size of the
REMBOX4 is 24" (61cm.) wide, 18-1/2" (47cm.) high
and 5" (12.7cm.) deep.
NRC Network Ring Card
NRC Network Ring Card
Model NRC (FM approval pending) provides XNET, peer-to-
peer communication between FireFinder XLS systems. One
(1) Model NRC is required for each XLS panel, in order to
allow FireFinder XLS nodes to be wired in a Class A, Style 7
ring topology.
NCC-G - Network Color Graphics
NCC-G - Network Color Graphics
NCC-G is a PC-based, color-graphics command center
designed for use with the XNET network, and provides full
control and annunciation for a XNET network for a
maximum 63 XLS, MXL-IQ or MXL systems. The NCC-G is
used to monitor and control alarms, troubles, security,
supervisory and all system events from one of many XLS
systems. The NCC-G maintains an extensive history log of
all system events and has extensive report generation
capabilities. User programmable function buttons allow
site specific control functions. Multiple NCC-Gs may be
connected to XNET network. Each NCC-G ordered
separately.
Temperature and Humidity Range
Products are UL 864 9th Edition listed for indoor dry
locations within a temperature range of 120+/-3°F
(49+/-2°C) to 32+/-3°F (0+/-2°C) and at a relative
humidity of 93+/-2% at a temperature of 90+/-3°F
(32+/-2°C).