PASCO ES-8086 Discover Charge Set User Manual
Discover charge set
Table of contents
Document Outline
- Discover Charge Set
- Model No. ES-8086
- Equipment List
- 1. Material sheets, 10 cm x 15 cm: Teflon, Styrene, Polyester, Wool, PVC
- Introduction
- Creating Charged Indicators
- 1. Cut a 10 cm strip of transparent tape and fold one cm over on itself to make a handle. Avoid t...
- 2. Label this tape T1.
- 3. Stick the strip of tape to the tabletop.
- 4. Cut a 9 cm strip of transparent tape and fold one cm over on itself to make a handle. Avoid to...
- 5. Label this tape T2.
- 6. Stick the second piece of tape directly on top of the first piece as shown.
- 7. Grasp the lower tape (T1) and quickly pull up from the table. Avoid touching the tape except b...
- 8. Quickly pull T2 away from T1, again trying not to touch either tape except by the handle.
- 9. Stick each tape to the edge of a table with the handle hanging freely as shown.
- 10. Through the above process, the lower tape (T1) is now negatively charged and the upper tape (...
- 11. The charged indicators are now ready to use with the five materials.
- Triboelectric Series
- Discovering Charge
- 1. Ask students to choose two of the materials.
- 2. Place one sheet in each hand and rub together for 20 seconds as shown.
- 3. Separate the materials and bring one near the negative indicator tape. Observe the behavior of...
- 4. Bring the same material near the positive indicator tape. Observe the behavior of the tape.
- 5. Record the charge of the 1st material.
- 6. Bring the second material near the negative indicator tape. Observe the behavior of the tape.
- 7. Bring the same material near the positive indicator tape. Observe the behavior of the tape.
- 8. Record the charge of the 2nd material.
- 9. Explain how the two materials became charged; include electrons in your explanation.
- 10. Place these two materials in the triboelectric series based on their behavior when rubbed tog...
- 11. Choose one new material and rub it against one of the materials already used.
- 12. Repeat steps 2-10 for these two materials.
- 13. Continue testing until all five materials are ranked within the triboelectric series.
- Conclusions
- 1. Explain how the materials become charged through their interaction with one another.
- 2. Ask students to explain in detail their process for ranking the materials. This explanation ca...
- Teacher Notes:
- Equipment List
- Model No. ES-8086
- 012-08899a_cvr.pdf
- 012-08899a_txt.pdf
- Discover Charge Set
- Model No. ES-8086
- Equipment List
- 1. Material sheets, 10 cm x 15 cm: Teflon, Styrene, Polyester, Wool, PVC
- Introduction
- Creating Charged Indicators
- 1. Cut a 10 cm strip of transparent tape and fold one cm over on itself to make a handle. Avoid t...
- 2. Label this tape T1.
- 3. Stick the strip of tape to the tabletop.
- 4. Cut a 9 cm strip of transparent tape and fold one cm over on itself to make a handle. Avoid to...
- 5. Label this tape T2.
- 6. Stick the second piece of tape directly on top of the first piece as shown below.
- 7. Grasp the lower tape (T1) and quickly pull up from the table. Avoid touching the tape except b...
- 8. Quickly pull T2 away from T1, again trying not to touch either tape except by the handle.
- 9. Stick each tape to the edge of a table with the handle hanging freely as shown below.
- 10. Through the above process, the lower tape (T1) is now negatively charged and the upper tape (...
- 11. Write a negative sign (-) on T1 and a positive sign (+) on T2.
- 12. The charged indicators are now ready to use with the five materials.
- Triboelectric Series
- Discovering Charge
- 1. Ask students to choose two of the materials.
- 2. Place one sheet in each hand and rub together for 20 seconds as shown below.
- 3. Separate the materials and bring one near the negative indicator tape. Observe the behavior of...
- 4. Bring the same material near the positive indicator tape. Observe the behavior of the tape.
- 5. Record the charge of the 1st material.
- 6. Bring the second material near the negative indicator tape. Observe the behavior of the tape.
- 7. Bring the same material near the positive indicator tape. Observe the behavior of the tape.
- 8. Record the charge of the 2nd material.
- 9. Explain how the two materials became charged; include electrons in your explanation.
- 10. Place these two materials in the triboelectric series based on their behavior when rubbed tog...
- 11. Choose one new material and rub it against one of the materials already used.
- 12. Repeat steps 2-10 for these two materials.
- 13. Continue testing until all five materials are ranked within the triboelectric series.
- Conclusions
- 1. Explain how the materials become charged through their interaction with one another.
- 2. Explain in detail the process for ranking the materials. This explanation can either be in par...
- Teacher Notes:
- Discover Charge Set
- 012-08899a_txt.pdf
- Discover Charge Set
- Model No. ES-8086
- Equipment List
- 1. Material sheets, 10 cm x 15 cm: Teflon, Styrene, Polyester, Wool, PVC
- Introduction
- Creating Charged Indicators
- 1. Cut a 10 cm strip of transparent tape and fold one cm over on itself to make a handle. Avoid t...
- 2. Label this tape T1.
- 3. Stick the strip of tape to the tabletop.
- 4. Cut a 9 cm strip of transparent tape and fold one cm over on itself to make a handle. Avoid to...
- 5. Label this tape T2.
- 6. Stick the second piece of tape directly on top of the first piece as shown below.
- 7. Grasp the lower tape (T1) and quickly pull up from the table. Avoid touching the tape except b...
- 8. Quickly pull T2 away from T1, again trying not to touch either tape except by the handle.
- 9. Stick each tape to the edge of a table with the handle hanging freely as shown below.
- 10. Through the above process, the lower tape (T1) is now negatively charged and the upper tape (...
- 11. Write a negative sign (-) on T1 and a positive sign (+) on T2.
- 12. The charged indicators are now ready to use with the five materials.
- Triboelectric Series
- Discovering Charge
- 1. Ask students to choose two of the materials.
- 2. Place one sheet in each hand and rub together for 20 seconds as shown below.
- 3. Separate the materials and bring one near the negative indicator tape. Observe the behavior of...
- 4. Bring the same material near the positive indicator tape. Observe the behavior of the tape.
- 5. Record the charge of the 1st material.
- 6. Bring the second material near the negative indicator tape. Observe the behavior of the tape.
- 7. Bring the same material near the positive indicator tape. Observe the behavior of the tape.
- 8. Record the charge of the 2nd material.
- 9. Explain how the two materials became charged; include electrons in your explanation.
- 10. Place these two materials in the triboelectric series based on their behavior when rubbed tog...
- 11. Choose one new material and rub it against one of the materials already used.
- 12. Repeat steps 2-10 for these two materials.
- 13. Continue testing until all five materials are ranked within the triboelectric series.
- Conclusions
- 1. Explain how the materials become charged through their interaction with one another.
- 2. Explain in detail the process for ranking the materials. This explanation can either be in par...
- Teacher Notes:
- Discover Charge Set