Pach and Company AeGIS 4000P Manual User Manual
Page 27

96
SYSTEM
ANSWER MODE
ENABLE OR
DISABLE THE
AUTO ANSWER
MODE. IF
DISABLE THE
SYSTEM WILL
NOT ANSWER
AN INCOMING
CALL FROM THE
OUTSIDE LINE.
97
DO NOT
DISTURB MODE
DISABLE OR
ENABLE THE
SYSTEM TO
CALL
“One Short Beep”. Refer to
Chapter 5 System’s Operation.
Step5
Enter another Function Code
to program another parameter
otherwise press
∗ to exit and you will
hear “Three Short Beeps”.
Step 1
Entering The Programming
Mode: Press 0 and # simultaneously
then release. If you are in the
programming mode, proceed to step 2.
Step 2
Enter the 4-digit Master
Code (factory default is 0000) and you
will hear “One Short Beep”. If you
entered an invalid master code you will
hear “One Long Beep”, repeat
step 1. Should your master code
become lost or forgotten see Reset
Master Code.
Step 3
Enter 96 then #, you will
hear “One Short Beep”.
Step 4
Enter 0 (system answer is
disabled) or 1, 2, 3 or….9 (system will
answer a remote call on 1st ring, 2nd
ring, 3rd ring…9th ring) then press #
and you will hear “One Short Beep”.
Step 5
Enter another Function Code
to program another parameter
otherwise press
∗ to exit and you will
hear “Three Short Beeps”.
Step 1
Entering The Programming
Mode: Press 0 and # simultaneously
then release. If you are in the
programming mode, proceed to step 2.
Step 2
Enter the 4-digit Master
Code (factory default is 0000) and you
will hear “One Short Beep”. If you
entered an invalid master code you will
hear “One Long Beep”, repeat
step 1. Should your master code
become lost or forgotten see Reset
Master Code.
Step 3
Enter 97 then #, you will
hear “One Short Beep”.
Step 4
Enter
0 to disable Do not Disturb Mode
(mode 0 is factory default setting)
1 to enable Do not Disturb Mode
(system will not call to a premise or
remote location)
then press #, you will hear “One Short
Beep”.
Step 5
Enter another Function Code
to program another parameter
otherwise press
∗ to exit and you will
The system number of rings to
answer a remote call can be
programmed from 1 to 9 rings or it
can also be disabled. You must
program the System Answer
Mode at the front panel
Step 1
Pick up the phone and wait
for a dial tone.
Step 2
Press # # and you will hear
“One Short Beep”.
Step 3
Press # and you will hear
“One Short Beep”.
Step 4
Enter the Function Code 97
then press #, you will hear “One Short
Beep”.
Step 5
Enter 0 (to disable) or 1 (to
enable) then press #, you will hear
“One Short Beep”.
Step 6
Enter another function code
to program a different parameter or
exit the program by pressing
∗ ∗ and
you will hear “Three
Short Beeps”.
Step 5
Enter another function
code to program a different parameter
or exit the program by pressing
∗ ∗
and you will hear “Three Short
Beeps”.
The system number of rings to
answer a remote call can be
programmed from 1 to 9 rings or it
can also be disabled. You must
program the System Answer
Mode at the front panel.
Step 1
Call to the AeGIS 4000P
system (you must know the system’s
phone number), you will hear: “One
Short Beep”, the gate is locked. “Two
Short Beeps”, the gate is unlocked.
Step 2
Press # then enter a valid
master code and you will hear:
• “One Short Beep”, the master code
is accepted then press # and you will
hear “One Short Beep”.
• “One Long Beep”, the master code
is rejected and the connection will be
disconnected.
Step 3
Enter the Function Code 97
then press #, you will hear “One Short
Beep”.
Step 4
Enter 0 (to disable) or 1 (to
enable) then press #, you will hear
“One Short Beep”.
Step 5
Enter another function code
to program a different parameter or
exit the program by pressing
∗ ∗ and
you will hear “Three Short Beeps”.
Function
Local Programming
Premise Phone
Remote Phone
Pach and Company
Page 19
AeGIS 4000P
Chapter 3. Programming