Pach and Company AeGIS 4000P Manual - Manual (Page 17)

01-20
INDIVIDUAL
ACCESS CODE
TO ACCESS
RELAY 1
(DOOR 1)
21-40
INDIVIDUAL
ACCESS CODE
TO ACCESS
RELAY 2
(DOOR 2)
41-50
INDIVIDUAL
ACCESS CODE
TO ACCESS
BOTH RELAY 1
AND 2 (DOOR 1
AND DOOR 2)
Step 3 Enter 00 then #, you will
hear “No Beep”.
Step 4 Enter new 4-digit Master
Code then press # then you will hear
“One Short Beep” and proceed to
step 5 or if you decided
not to change the existing Master
Code press
∗ to exit and you will hear
“Three Short Beeps”.
Step 5 Continue to program another
parameter or press ∗ to exit; you will
hear “Three Short Beeps”.
Step 1 Entering The Programming
Mode: Press 0 and # simultaneously
then release. If you are in the pro-
gramming mode, proceed to step 2.
Step 2 Enter the 4-digit Master
Code (factory default is 0000) and you
will hear “One Short Beep”. If you
entered an invalid master code you will
hear “One Long Beep”, repeat
step 1. Should your master code
become lost or forgotten see section
Reset Master Code.
Step 3 Enter the Index Number
(01 – 20, 21-40 or 41-50) then #, you
will hear “No Beep”. If the associated
Index Number has an access code
programmed, you will hear “Two Long
Beeps”. Press
∗, you will hear “One
Short Beep” and select another Index
Number.
Step 4 Enter the 4-digit access
code then #, you will hear “One
Beep”.
Do not program the same code as in
index01-20, 21-40 and 41-50, doing
so the access code programmed
won’t work.
Step 5 Return to step 3 to program
another access code or enter another
Function Code to program another
parameter, otherwise
press
∗ to exit and you will hear
“Three Short Beeps
Step 1 Pick up the phone and wait
for dial tone.
Step 2 Press # # and you will hear
“One Short Beep”.
Step 3 Press # and you will hear
“One Short Beep”.
Step 4 Enter the 01-20, 20-21 or
41-50) then press #, you will hear “No
Beep”: the index numbers is empty
and proceed to Step 5. “Two Long
Beeps”: the index number is not
empty and you must do one of the
following:
• Press 1 then # you will hear “No
Beep” to overwrite existing access
code and proceed to Step 4.
• Press ∗ ∗ you will “One Short Beep”
and repeat this step.
Step 5 Enter the 4-digit access
code number then press #, you will
hear “One Short Beep”.
Do not program the same code as in
index 01-20, 21-40 and 41-50, doing
so the access code programmed
won’t work.
Step 6 Return to step 4 to program
another access code or enter another
function code to program different
parameter or exit the
program by pressing
∗ ∗ and you will
hear “Three Short Beeps”.
Pach and Company Page 9
AeGIS 4000P Chapter 3. Programming
Step 1 Call to the AeGIS 4000P
system (you must know the system’s
phone number), you will hear: “One
Short Beep”, the gate is locked. “Two
Short Beeps”, the gate is unlocked.
Step 2 Press # then enter a valid
master code and you will hear:
• “One Short Beep”, the master code
is accepted then press # and you will
hear “One Short Beep” .
• “One Long Beep”, the master code
is rejected and the connection will be
disconnected.
Step 3 Press # to enter into the pro-
gramming mode and you will hear
“One Short Beep” or
∗∗ to hang-up
the call.
Step 4 Enter the 01-20, 21-40, or
41-50then press #, you will hear “No
Beep”: the index numbers is empty
and proceed to Step 5. “Two Long
Beeps”: the index number is not
empty and you must do one of the
following:
• Press 1 then # you will hear “No
Beep” to overwrite existing access
code and proceed to Step 4.
• Press ∗ ∗ you will “One Short Beep”
and repeat this step.
Step 5 Enter the 4-digit access
code number then press #, you will
hear “One Short Beep”.
Do not program the same code as in
index 01-20, 21-40 and 41-50, doing
so the access code programmed
won’t work.
Step 6 Return to step 4 to program
another access code or enter another
function code to program different
parameter or exit the
program by pressing
∗ ∗ and you will
hear “Three Short Beeps”.
Function Local Programming Premise Phone Remote Phone
Program
Individual
Access Code