Pach and Company AeGIS 8000 Series Quick Guide - Manual

TECHNICAL SUPPORT IS AVAILABLE MON-FRI
7:30AM-3:30PM PST AT 1-888-678-7224
by Pach & Co . Quick Guide
 Parts above are only
included on complete
system (8250)
 Missing Parts, contact Pach
and Company 1-888-678-
7224
 Defective system under
manufacturer warranty,
call 1-888-678-7224 for
advance replacement

24 Months warranty for
complete system
 6 Months warranty for
Printed Circuit Board
(8PCB250)

Manuals, management
software, catalog are on CD
or download at www.pach-
co.com
Red button is Master Code retrieval button. See also diagram.
What is Master Code: 4- digit code to log-on to programming mode
(0000 is default)
What is Dir (directory code): 2, 3, or 4 digit number see function
code 09. The number can be associated to apartment no., first three
digit of phone no., last four digit of phone no. , or any random no.
assigned to each tenants. Every tenant must have different directory
code no..
What is Access Code: 4-digit code for tenant to open the door or
gate.
Exit program, clear field,
reset keystroke.
17 Set system date
Save program 19
Initialize event recording
buffer
00
Change master code
(0000 is default)
20
Remote unlock relay 1
(1-9, 9 is default)
01 Add new tenant 21
Remote unlock relay 2
(1-9, 8 is default)
02 Edit existing tenant 40
Master code mask.
Warning: read manual
for more detail.
03 Delete existing tenant 46
Display system’s
information
04 Clear all tenants 50
Clear memory to factory
default
05
Manual unlock/lock relay 1
with timer (01-98 hours, 99
hours unlock hold, 00
hours to lock)
70
Select Modem Protocol
V22 or B212
06 Manual unlock/lock relay 2 71 Enable Disable Modem
07
Single or multi system
(single is default)
72
Invalid code lock-out
count (1-9). 3 is default
08 System ID number (n/a) 73
Tone/pulse dialing.
Tone is default
09
Directory digit (2, 3 or 4
digit, 3 digit is default)
74
Enable/disable auto
answer. Enable is
default
10 Edit scrolling message 75
Enable/disable keypad
press beep. Enable is
default
11
Relay 1 unlock interval
(04-99 seconds, 12
seconds is default)
76
Enable/disable speaker
beep. Enable is default
12 Relay 2 unlock interval 77
Enable/disable PBX.
Disable is default
14 Set system clock 78
View name and
directory
15 Day light saving 79
Talk time (10-180
seconds). 60 second is
default
16 Display current time 91
Total number of tenant.
Tenant with no name
will not be included
Log on to programming: Press
simultaneously then release, welcome
message will stop scrolling (repeat if screen
still scrolls) enter 4-digit “
MASTER CODE ”
(0000 is default), the screen will show:
Select the “
Function Code ” from the table
Two ways call from the system
1. Press to scroll name from A-Z or to scroll name from
Z-A then press to call name selected.
2. Press wait for dial tone then press the directory no.
Opening the door remotely press to release relay 1
(door 1) or to release relay 2 (door 2).
Opening the door using the access code press (display
screen will stop scrolling) then press a valid 4-digit access
code.
Extending talk time tenant must press from the phone
after the time out warning beep.
Calling into the system : incase you are not available when
your visitor call you. Follow steps below to use this feature
1. The system modem must be disabled and function 74 (auto
answer must be enabled).
2. Call the system’s phone no., you will hear “ONE BEEP”, then
press to talk to your visitor. Press or to release
the door
1. Press after selecting a letter or character.
2. You have 30 seconds to enter each letter or character.
3. Letter QZ, numeric 0-9 and punctuations press
4. Press space and for backspace