Dings Dynamics Group 70 Series Coupler NEMA 4 - Manual (Page 4)

Table 2. Parts List
* Number of rotating discs is designated by model number; example:6-72025-38 has two rotating discs.
Also see table 1 for number of rotating discs.
** Number of stationary discs is one less than the number of rotating discs.
4740 WEST ELECTRIC AVENUE
MILWAUKEE, WI 53219
PHONE 414/672-7830 FAX 414/672-5354
www. dingsbrakes.com
ITEM
NO.
PCS.
REQ’D
DESCRIPTION
PART NUMBER
NEMA 2 NEMA 4
1 1
Hub & shaft assembly
(Specify both diameters & keyways)
Consult Factory
2 1 Bracket (Specify brake model no.) L070203
3 2 Studs (Specify brake model no.) H070180
4 * Rotating friction disc H070103-008
5 ** Stationary disc K070485-001
6 1 Pressure plate assembly K070045-001
7 2 Torque spring See torque spring table
8 2 Torque spring washer W004004-001
9 2 Torque adjusting nut W003001-022
10 2 Manual release rod G070472-001
11 2 Manual release spring G060010-001
12 2 Manual release washer W004004-003
13 As Req’d Manual release shims- .006” thick W004004-004
14 2 Manaul release stop screw G060029-001
15 2 Manual release lockwasher W004007-007
16 2 Manual release knob G070471-001
17 2 Roll pin, 3/32 x 9/16 lg. W005003-039
18 1
Magnet mounting plate assembly
for 3-Phase magnets (Includes items 19-20)
K070097
18 1
Magnet mounting plate assembly
for 1-Phase magnets (Includes items 19-22)
K070335
19 1 Roll pin, 5/32 x 1/-18 lg. W005003-109
20 2 Coils-single phase (See ordering info.) H070013
20 6 Coils-three phase (See ordering info.) H020003
21 2 Insulating washers, 1-Phase coils G070029-001
22 2 Shading coil (single phse only) G070032-001
23 2 Hex jam nut 1/2-20 W003003-023
24 2 ESNA locknut 1/2-20 W003001-020
25 1 Adapter housing (1-1/8 output shaft) L070202-002
25 1 Adapter housing (1-3/8 output shaft) L070212-002
26 1 ESNA locknut 1/2-20 W003001-020
27 1 Ball bearing-double seal (1-1/8 output shaft) W009001-002
28 1 Retaining ring (1-1/8 output shaft) W006004-001
29 1 Retaining ring (1-1/8 output shaft) W006002-002
30 1 Wrap cover K070228-001 K070279-001
31 1 Nameplate with two drive screws K060473-001
32 1 Cap plug W008003-001
33 1 Pipe plug - 1/8 NPT W010002-001
34 1 “O” ring W006001-010
35 2 Gasket for brake mounting K070250
36 2 Gasket W011004-001
37 2 RD. HD. screw, #10-32 x 1” lg. W001002-080
38 2 hex nut #10-32 W003001-011
39 1 Ball bearing-double seal (1-3/8 output shaft) W009001-003
40 1 Retaining ring (1-3/8 output shaft) W006002-003
41 2 Retaining ring (1-3/8 output shaft) W006007-003
Model
Number
NEMA 2
Model
Number
NEMA 4
Torque
Spring P/N
6-71010-38 4-71010-46 G070011-001
6-71015-38 4-71015-46 G070012-001
6-72025-38 4-72025-46 G070019-001
6-73025-38 4-73025-46 G070525-001
6-72035-38 4-72035-46 G070012-001
6-73035-38 4-73035-56 G070011-001
6-73050-38 4-73050-46 G070012-001
6-74075-38 4-74075-46 G070012-001
Torque spring (Item 7) table