Magnum Venus Plastech System One FRP 4102-00-01 - Manual (Page 6)

FRP SystemOne
7. Remove and discard the 9201-1-5 (5/32” SS Ball).
8. Remove and retain the 4101-3-1 (Piston Rod Spring).
9. Unscrew the 4102-3-1 (Packing Nut) and pull the 4102-2-1 (Piston
Rod) out of the 4101-14-1 (Outlet Body). Carefully pull the Piston
Rod out of Cylinder to avoid damaging the interior surface of
Cylinder. Inspect the Piston Rod for scratches or other damage
and replace if necessary.
10. Insert a 1/4” dia. Dowel into the bottom of the 4101-14-1 (Outlet
Body), force the 4102-5-01 (Piston Rod Packings) and 4102-4-1
(Upper Guide) out through the top of the Outlet Body and discard.
11. Unscrew the 4102-6-1 (Cylinder) from the 4101-7-1 (Inlet Body).
Remove and discard the two 7301-9-014 (O-Rings). Inspect the
Cylinder for scratches, or other damage, and replace if necessary.
12. Remove and discard the 9201-1-14 (7/16” SS Ball). Inspect the
seat inside the 4101-7-1 Inlet Body, for nicks, scratches, or other
damage, and lap, or replace if necessary.
13. Remove the 4101-8-1 (Inlet Tube Fitting). Remove and discard the
7301-9-013 (O-Ring).
3
WARNING
Use wrench flats provided in order to avoid damaging the Piston Use wrench flats provided in order to avoid damaging the Piston Use wrench flats provided in order to avoid damaging the Piston Use wrench flats provided in order to avoid damaging the Piston Use wrench flats provided in order to avoid damaging the Piston
Rod. Rod. Rod. Rod. Rod.
NOTE
Car Car Car Car Care m e m e m e m e must be tak ust be tak ust be tak ust be tak ust be taken to not dama en to not dama en to not dama en to not dama en to not damag gg gge the inside of e the inside of e the inside of e the inside of e the inside of the Outlet Bod the Outlet Bod the Outlet Bod the Outlet Bod the Outlet Bodyyyyy.....
NOTE
Once disassembly is complete all parts should be flushed in Once disassembly is complete all parts should be flushed in Once disassembly is complete all parts should be flushed in Once disassembly is complete all parts should be flushed in Once disassembly is complete all parts should be flushed in
distilled water and inspected for damage and replaced if distilled water and inspected for damage and replaced if distilled water and inspected for damage and replaced if distilled water and inspected for damage and replaced if distilled water and inspected for damage and replaced if
necessar necessar necessar necessar necessaryyyyy.....
NOTE
Carefully pull the Piston Rod out of Cylinder to avoid damaging Carefully pull the Piston Rod out of Cylinder to avoid damaging Carefully pull the Piston Rod out of Cylinder to avoid damaging Carefully pull the Piston Rod out of Cylinder to avoid damaging Carefully pull the Piston Rod out of Cylinder to avoid damaging
the interior surf the interior surf the interior surf the interior surf the interior surface of ace of ace of ace of ace of Cylinder Cylinder Cylinder Cylinder Cylinder..... Inspect the Piston R Inspect the Piston R Inspect the Piston R Inspect the Piston R Inspect the Piston Rod f od f od f od f od for or or or or
scr scr scr scr scra aa aatc tc tc tc tches or other dama hes or other dama hes or other dama hes or other dama hes or other damag gg gge ee ee..... R R R R Re ee eeplace if place if place if place if place if necessar necessar necessar necessar necessaryyyyy.....