Level Mount LM50HDCC - Manual

Installation instructions
Fixed/Tilt Plasma/LCD Wall Mount
Model: FT65-03*, FT65B-CC*, ELLCDM-
07,ELLCDP-07, LM50CDM, DC50CDM,
LM60T, DC60T, LM65FT*, DC65FT*
DO NOT RETURN THIS PRODUCT TO THE STORE OR WEB
SITE YOU PURCHASED IT FROM!
IF YOU BELIEVE THIS MOUNT IS DEFECTIVE, HAS
MISSING OR BROKEN PARTS, OR IF YOU ARE HAVING
DIFFICULTY INSTALLING THIS MOUNT TO YOUR WALL
OR FITTING YOUR TV, PLEASE CONTACT OUR COMPANY,
LEVEL MOUNT, DIRECTLY.
Dial 1 888 229 1459 or email us at CustomerSupport@
ElexaUSA.com any time of the day or night for a quick and
efficient solution to your problem.
Our trained Customer Service Department is open 24 hours
a day, 7 days a week, every day of the year and is prepared
to assist you in both English and Spanish.
Please also visit our Web Site at www.LevelMount.com
for assistance.
Features:
• Integrated Bubble Level
• Durable Steel Construction
• Easy 2 Piece Mounting
• Tilts up to 30 degrees
• Locking Lever
• Stud Finder Included
Mounting Equipment Included:
Bag REF
Description QTY
1 A Phillips M4 x 12 Bolt 4
B Phillips M4 x 20 Bolt 4
C Phillips M4 x 30 Bolt 4
2 D Phillips M5 x 12 Bolt 4
E Phillips M5 x 20 Bolt 4
F Phillips M5 x 30 Bolt 4
3 G Phillips M6 x 12 Bolt 4
H Phillips M6 x 24 Bolt 4
I Phillips M6 x 35 Bolt 4
4 J Phillips M8 x 25 Bolt 4
K Phillips M8 x 40 Bolt 4
5 L M4/M5 Washer 4
M M4/M5 Spacer 4
5 N M6/M8 Spacer 4
1 O M4 Lock Washer 4
2 P M5 Lock Washer 4
3 Q M6 Lock Washer 4
4 R M8 Lock Washer 4
S 3’’ Hex Screw 6
6 T Hex Washer 6
U Concrete Anchor 6
V M5 x 48 Bolt 8
7* W M5 Hex Nut 8
X M5 Washer 8
Y L-Shape Bar Lock 2
8 Z Phillips screws M5 x 10 Bolt 4
AA M5 Hex Nut 2
BB M5 Butterfly Nut
2
Tools required for attachment to stud:
1/2’’ (12mm) Socket Wrench
Stud finder
Tools required for attaching to concrete:
Electric drill
1/2’’ (12mm) Masonry Bit
CAUTION:
Installer must make sure the LCD Wall Mount is proper-
ly and securely attached and that appropriate fasteners
are used. It is the responsibility of the installer to verify
that the mount is anchored properly to the wall.
PLEASE NOTE: THE MOUNT MUST BE ATTACHED
TO WOOD STUDS OR TO PROPERLY INSTALLED
ANCHORS IN CONCRETE. DO NOT MOUNT ONLY
TO DRYWALL.
Before installing, check to make sure all parts of the
mount are included.
Make sure all screws and bolts are tightened before
allowing Wall Mount to bear the full weight of the
LCD Display.
Attaching Wall Plate to Wooden Studs:
1a. Locate wall studs: Locate a proper place to mount by
using the included stud finder (Figure 1) It is recom-
mended that the center of the stud be used – and that
a nail be used to verify that a stud has been located.
The mount requires a minimum of two studs to ensure
proper and safe installation. The tilt arms will adjust
horizontally to the right and left up to 8 inches after
you determine the desired viewing location.
Attaching LevelMount to wall: Once the Wall Plate is
in the correct position on the studs, screw 1 Hex Screw
and 1 Hex Washer (P & Q) in the upper left mounting
hole of the Wall Plate into the stud. Do not screw too
tight until after all the screws are in. Drill pilot hole with
1/8 inch drill bit.
Using the Bubble Level as your guide (Figure 3, page
2), drive the 2nd screw into the opposite upper right
hand mounting hole of the Wall Plate. Now tighten
both screws, proceed to drive the remaining 2 screws
into the studs as seen in figure 2, page 1.
Figure 1
NOTE: Due to the weight of the LCD/Plasma TV’s, it is
necessary to mount the Wall Plate to at least 2 studs.
Attaching Wall Plate to Concrete:
1b. Attaching Wall Mount to concretel: Place the Wall
Plate at the height you want to install the Plasma/LCD
wall Mount. Mark the six holes you will be using for
concrete anchors (Figure 4). Utilize the built-in bubble
level to ensure proper mounting (Figure 3). Drill holes
for the concrete anchors using an electric drill with a
masonry bit (1/2’’ or 12mm (Figure 5). Drill into the wall
at least as deep as the screw is long (3 inches).
Insert the anchors into the holes and set them flush to
the wall by tapping them in with a hammer (Figure 6).
Once the Wall Plate is in the correct position on the
wall, screw 1 Dry Wall Screw and 1 Dry Wall Washer
(P & Q) in the upper left mounting hole of the
Wall Plate. Do not screw too tight until all the screws
are in.
Drive the 2nd screw into the opposite upper right hand
mounting hole of the Wall Plate, then proceed to drive
the remaining 4 screws into the concrete anchors as
seen in figure 2. Make sure all screws are tightened.
Figure 2
Figure 3
Figure 4
Figure 5
Figure 6
2. Selecting the Appropriate Hardware for your LCD/
Plasma: CAUTION: Select Bag 1-4, which most resem-
bles the hole side on the back of your LCD/Plasma.
Thread the bolts carefully into your LCD or plasma by
hand to determine which provided mount hardware
(correct diameter) is appropriate for installation. If you
feel resistance, remove the bolt immediately! Next
determine the correct length of the required bolt as
described in the following step.
*Bag 7 only included with models FT65-03, FT65B-CC,
LM65FT and DC65FT
**PLEASE NOTE: You will not use all of the hardware
included. Please see last page of the manual if your
Plasma or LCD needs extension arms.
Tilt
Arms
Wall Plate
Cord
Management
S
T
U
www.LevelMount.com
1-888-229-1459
©2008 Level Mount
Patents Pending
English
CAUTION
This wall mount was designed
specifically to hold LCD TV’s 34” - 65” and a maximum
weight of up to 200lbs.Using this product with a TV
heavier than the maximum weight may result in injury.
!