Controlled Products Systems Group 1024 - Manual (Page 23)

PN# 3642036534, 02/26/2010 REV. 1
23
FCC and IC CERTIFIED
FIG. 7-1 Learn code button and LED
SET
SET
OPEN
FORCE
CLOSE CODE
LEARN LIMIT MANUAL
Open
Travel Limit
Open
Set Limit
Button
Close
Travel Limit
Close
Set Limit
Button
Down Force
Control
Adjustment
Up Force
Control
Adjustment
Learn
Code
Button
LED
Indicator Light
To
Garage Door
This device complies with FCC Part 15 and RSS 210
of Industry Canada. This equipment has been tested
and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will
not occur in a particular installation. If this equipment
does cause harmful interference to radio or television
reception, which may be determined by turning the
equipment OFF and ON, the user is encouraged to
try to correct the interference by one or more of the
following measures:
‡ Re-orient or relocate the receiver antenna.
‡ Increase the separation between the opener
and receiver.
‡ Connect the opener into an outlet on a circuit
different from that to which the receiver is
connected.
‡ Consult your local dealer.
ROGRAMMING REMOTE CONTROLS
7
NOTE: For remote control locate Box 3.
1a. Single Button Remote Programming.
NOTE: This opener can learn up to 7 transmitter
buttons.
‡ Locate “Learn Code” button and indicator
LED on the power head (Fig. 7-1).
‡ Press and release “Learn Code” button.
– Indicator LED will blink RED at a rate of twice
per second.
‡ Within 30 seconds, push remote control
button once.
– Indicator LED will stop blinking and stay ON.
‡ Press remote control button again.
‡ Press remote control button again, door will move.
– Red LED will go out. Remote is now
programmed and ready for use.
1b. Multi Button Remote Programming.
NOTE: Each button on a multi-button remote is
designed for use with 1 door. You cannot
program 2 buttons to operate the same door, nor
can you program 1 button to operate 2 doors.
You can program a maximum of 7 different
transmitters or wireless devices.
NOTE: Pushing two buttons on power head
simultaneously will erase programmed memory and
limits must be reset.
‡ For each button .
– Program each button separately using the
Single Button Remote Programming steps.
2. Operating.
‡ Press remote button once.
– Door will move.
‡ Press button again.
– Door will stop.
‡ Press button again.
– Door will move in opposite direction.
NOTE: The door will stop automatically at the
fully open or fully closed position.
CODE
LEARN
A moving door can cause serious injury or death.
1. Keep people clear of opening while door is
moving.
2. Do NOT allow children to play with opener,
including wall button, remote control, or
Wireless Keypad.
3. During programming, the door opener could
begin to run, so keep people and objects away
from the moving door and its parts. To keep the
door from moving, close the door and
disconnect it from the Opener by pulling the
Emergency Release.
WARNING
LOST OR STOLEN REMOTE
1. Clear memory.
‡ Press and hold learn code button (on power
head) for 10 seconds or until the red blinking
indicator LED goes out.
‡ Program remaining or new remote controls as
done previously. Your door opener will no
longer recognize any signal received from the
missing remote control, or any other which has
not been reprogrammed.
NOTE: To program a
Homelink
® and Car2U ®
device follow the Homelink ® or Car2U ®
instructions in your car owner’s manual.
Limit controls location
on power head.