Atec Tektronix-TDS6804B - Manual (Page 9)

Digital Storage Oscilloscopes • www.tektronix.com/oscilloscopes 9
Digital Storage Oscilloscope
TDS6000B/C Series
Recovered Clock –
SMA connector,
≤1.25 Gb/s, Output swing
≥130 mV
pk-pk
into 50 Ω. Requires Opt. SM or
Opt. ST to enable.
Recovered Data –
SMA connector,
≤1.25 Gb/s, Output swing of 1010
repeating pattern 200 mV into 50 Ω. Requires Opt.
SM or Opt. ST to enable.
DC Probe Calibration Output –
BNC connector, ±10 V DC for DC probe calibration.
(Signal available only during probe calibration.)
AUX Trigger Output –
BNC connector, provides a TTL-compatible, polarity
switchable pulse when the oscilloscope triggers.
USB2.0 Port –
One in front. Allows connection or disconnection
of USB keyboard, mouse or storage device while
oscilloscope is on.
Rear Panel
External Time Base Reference In –
BNC connector; allows time base system to phase-
lock to external 10 MHz reference.
Time Base Reference Out –
BNC connector; provides TTL-compatible output
of internal 10 MHz reference oscillator.
Aux Trigger Input – BNC, see Ext Trigger specification.
Parallel Port – IEEE 1284, DB-25 connector.
Audio Ports –
Miniature phone jacks for stereo microphone input
and stereo line output.
USB2.0 Ports –
Four in back. Allows connection or disconnection
of USB keyboard, mouse, or storage device while
oscilloscope power is on.
Keyboard Port – PS-2 compatible.
Mouse Port – PS-2 compatible.
LAN Port –
RJ-45 connector, supports 10Base-T, 100Base-T
and 1000Base-T.
Serial Port – DB-9 COM1 port.
Windows Video Port –
15-Pin D-sub connector on the rear panel;
connect a second monitor to use dual-monitor
display mode allowing analysis results and plots
to be viewed along with the oscilloscope display.
Video is DDC2B compliant.
GPIB Port – IEEE 488.2 standard.
Scope XGA Video Port –
15-Pin D-sub connector on the rear panel, video
is IBM XGA compatible. Connect to show the oscillo-
scope display, including live waveforms on an
external monitor or projector. The primary Windows
desktop can also be displayed on an external
monitor using this port.
Power Source
Power –
100 to 240 V
RMS
, ±10%, 50/60 Hz; 115 V
RMS
±10%,
400 Hz; CAT II, <500 W typical (650 VA).
Option SM
156 Standards Masks Supported –
ITU-T (1.544 Mb/s to 155 Mb/s).
ANSI T1.102 (1.544 Mb/s to 155 Mb/s).
Ethernet IEEE Std 802.3, ANSI X3.263 (1.544 Mb/s
to 3.125 Gb/s XAUI).
Sonet/SDH (51.84 Mb/s to 2.4883 Gb/s).
Fibre Channel (133 Mb/s to 4.25 Gb/s*
3 ).
InfiniBand (2.5 Gb/s).
USB (12 Mb/s to 480 Mb/s).
Serial ATA (1.5 Gb/s, 3.0 Gb/s).
Serial Attached SCSI (1.5 Gb/s, 3.0 Gb/s).
IEEE 1394b (491.5 Mb/s to 1.966 Gb/s).
RapidI/O (1.25 Gb/s to 3.125 Gb/s).
OIF Standards (2.488 Gb/s to 3.11 Gb/s).
PCI Express (2.5 Gb/s).
Physical Characteristics
BENCHTOP CONFIGURATION
Dimensions
mm in.
Height 282 11.1
Width 457 18.0
Depth 540 23.25
Weight kg lb.
Net 21 47
Shipping 32.3 71.2
RACKMOUNT CONFIGURATION
Dimensions
mm in.
Height 267 10.5
Width 491 19.3
Depth 638 25.1
Weight kg lb.
Net 22 49
Kit 5.6 12.25
*3 4.25 Gb/s mask supported using Glitch Trigger.
Mechanical
Cooling -
Required Clearance
mm in.
Top 0 or >76 0 or >3
Bottom 25 1
Left side 76 3
Right side 76 3
Front 0 0
Rear 0 0
Environmental
Temperature
Operating –
Excluding CD-R/W drive:
TDS6000B models: +5 ºC to +40 ºC.
TDS6000C models: +10 ºC to +45 ºC.
Including CD-R/W drive: +10 ºC to +40 ºC.
Nonoperating – –22 ºC to +60 ºC.
Humidity
Operating –
20% to 80% relative humidity with a maximum wet
bulb temperature of +29 ºC at or below +50 ºC,
noncondensing. Upper limit derated to 25% relative
humidity at +50 ºC.
Nonoperating –
5% to 90% relative humidity with a maximum wet
bulb temperature of +29 ºC at or below +60 ºC,
noncondensing. Upper limit derated to 20% relative
humidity at +60 ºC.
Altitude
Operating – 10,000 ft. (3,048 m).
Nonoperating – 40,000 ft. (12,190 m).
Random Vibration
Operating –
0.000125 g
2 /Hz from 5 to 350 Hz, –3 dB/octave
from 350 to 500 Hz, 0.0000876 g 2 /Hz at 500 Hz.
Overall level of 0.24 g
RMS
.
Nonoperating –
0.0175 g
2 /Hz from 5 to 100 Hz, –3 dB/octave from
100 to 200 Hz, 0.00875 g 2 /Hz from 200 to 350 Hz,
–3 dB/octave from 350 to 500 Hz, 0.006132 g 2 /Hz
at 500 Hz. Overall level of 2.28 g
RMS
.
Certifications
Electromagnetic Compatibility – 89/336/EEC.
Safety –
UL 3111-1, CSA1010.1, EN61010-1, IEC 61010-1.