Atec Panametrics-Olympus-Epoch-1000i - Manual (Page 11)

11
Ordering Information
The Mini‑Wheel encoder has been designed specifically for use with a variety of instruments. EPOCH 1000i users will require an adaptor
cable to use this encoder.
Cable
Number
Item
Number
Description
Cable
Length (m)
CABL‑10016‑0008 U8801209 EPOCH 1000i Mini‑Wheel encoder adaptor cable 0.15
ENC1‑2.5‑DE U8780197 Mini encoder, 2.5 m cable, DE15 connector for OmniScan MX 2.5
ENC1‑5‑DE U8780198 Mini encoder, 5.0 m cable, DE15 connector for OmniScan MX 5.0
Wedges for Manual Inspection
Wedge
Number
Item
Number
Matching Probe(s)
Nominal Refracted
Beam Angle
(in steel)
Sweep (°)
Probe
Orientation
Dimensions in mm (in.)
L x W x H
SA10P‑0L U8720704
2.25L8‑A10P, 5L16‑A10P,
10L16‑A10P
0° LW –30 to 30 Normal 25.4 (1.0) 23.1 (0.91) 20 (0.79)
SA10P‑N55S U8720705
2.25L8‑A10P, 5L16‑A10P,
10L16‑A10P
55° SW 30 to 70 Normal 23 (0.91) 23.2 (0.91) 14.2 (0.56)
SAWS1‑0L U8700264 2.25L16‑AWS1 0° LW –30 to 30 Normal 38 (1.49) 37.6 (1.48) 40 (1.57)
SAWS1‑N60S U8720552 2.25L16‑AWS1 55° SW 30 to 70 Normal 45.3 (1.78) 38 (1.49) 30.3 (1.19)
Wedges for Encoded Inspection
The wedges listed below have threaded inserts for connection to encoders. These wedges must be used for encoded inspection setups.
Wedge
Number
Item
Number
Matching
Probe(s)
Nominal
Refracted
Beam Angle
Sweep (°)
Probe
Orientation
Dimensions in mm (in.)
L x W x H
Removable
IHC Ring
SA10‑0L U8720544
2.25L8‑A10P, 5L16‑A10P,
10L16‑A10P
0° LW –30 to 30 Normal
25.4
(1.0) 23
(0.91) 20
(0.79)
SA10‑IHC
SA10‑N55S U8720545
2.25L8‑A10P, 5L16‑A10P,
10L16‑A10P
55° SW 30 to 70 Normal
23
(0.91) 23
(0.91) 14.2
(0.56)
SA10‑IHC
SA12‑0L U8720549 5L64‑A12 0° LW –30 to 30 Normal
61.8
(2.43) 23
(0.91) 53.4
(2.1)
SA12‑IHC
SA12‑N55S U8720550 5L64‑A12 55° SW 30 to 70 Normal
58
(2.28) 23
(0.91) 23
(0.91)
SA12‑IHC
Mini-Wheel Encoder
The Mini‑Wheel encoder can be used with the encoded C‑scan
option for the positioning and dimensioning of defects in the scan
axis, and can synchronize data acquisition with probe movement.
The Mini‑Wheel encoder is waterproof and can be mounted
onto the Olympus PA wedges using the included bracket kit. This
miniature encoder is made entirely of stainless steel, and features
sealed bearings for long‑lasting smooth operation. The custom
electronic circuit was designed for minimal noise induction.
Features
• Waterproof (designed for IP68 rating).
• Small footprint dimensions.
• Double O‑ring tire for better adherence.
• Sealed bearing for long‑lasting smooth wheel rotation.
• Strain relief for cable protection.
• Two M3 threaded holes on top of the casing for rigid
attachment.
Standard Inclusions
• 1 Encoder with standard wheel
• 1 Bracket kit
• 1 Allen key screwdriver for bracket attachment
• 1 Carrying case