Atec EXFO-FTB-8510B - Manual (Page 7)

FTB-8510B Packet Blazer
ETHERNET FUNCTIONAL SPECIFICATIONS
Note
a. Available as a software option.
TESTING
EtherSAM (ITU-T Y.1564) Capability to perform the service configuration test, including the ramp and burst tests, and service performance test as per ITU-T Y.1564.
Tests can be performed to a loopback or dual test set mode for bidirectional results.
RFC 2544 Throughput, back-to-back, frame loss and latency measurements according to RFC 2544 (bidirectional).
Frame size: RFC-defined sizes, user-configurable (bidirectional).
BERT Unframed. Layer 1 to layer 4 with or without VLAN Q-in-Q.
Patterns (BERT) PRBS 2E9-1, PRBS 2E11-1, PRBS 2E15-1, PRBS 2E20-1, PRBS 2E23-1, PRBS 2E31-1, CRPAT, CSPAT, CJTPAT, Short CRTPAT,
Long CRTPAT and up to 10 user patterns. Capability to invert patterns.
Error insertion (BERT) FCS, bit and symbol.
Error measurement Jabber/giant, runt, undersize, oversize, FCS, symbol, idle, carrier sense, alignment, collision, late collision, excessive collision, UDP,
TCP and IP header checksum.
Error measurement (BERT) Bit error, symbol error, idle error, bit mismatch 0, bit mismatch 1, performance monitoring (G.821 and G.826).
Alarm insertion (BERT) LOS, pattern loss.
Alarm detection LOS, link down, pattern loss, no traffic.
Service disruption time
measurement (BERT) Defect or No Traffic mode. Disruption time statistics include shortest, longest, last, average, total and count.
Multistream generation Capability to transmit up to ten streams. Configuration parameters are: packet size, transmission mode (N-Frames, Burst, N-Burst, Ramp,
N-Ramp and Continuous), MAC source/destination address, VLAN ID, VLAN priority, IP source/destination address, ToS field, DSCP field,
TTL, UDP/TCP source/destination port and payload. Selectable predefined stream profiles for voice, video and data streams. VoIP codecs
(G.711, G.723, G.729), video (MPEG-2 SDTV, MPEG-2 HDTV, MPEG-4 HDTV).
Multistream analysis Capability to analyze packet jitter, latency, throughput, frame loss and out-of-sequence per-stream statistics.
VLAN stacking (Q-in-Q) Capability to generate streams with up to three layers of VLAN (including IEEE802.1ad Q-in-Q tagged VLAN) and to filter received traffic
by VLAN ID or VLAN priority at any of the stacked VLAN layers.
PBB-TE a Capability to generate and analyze streams with PBB-TE data traffic including configuration of B-MAC (source and destination), B-VLAN
and I-tag (as per 802.1ah) and to filter received traffic by any of these fields.
MPLS a Capability to generate and analyze streams with up to two layers of MPLS labels and to filter received traffic by MPLS label or COS.
IPv6 a Capability to perform BERT, RFC 2544, traffic generation and analysis and Smart Loopback tests over IPv6.
Ping, traceroute, neighbor discovery and stateless auto-configuration.
Traffic filtering Capability to analyze the incoming traffic and provide statistics according to a set of up to ten configurable filters. Filters can be configured
for MAC source/destination address, VLAN ID, VLAN priority, IP source/destination address, ToS field, DSCP field, TCP source/destination
port and UDP source/destination port. VLAN filtering can be applied to any of the stacked VLAN layers.
Ethernet statistics Multicast, broadcast, unicast, N-unicast, pause frame, frame size distribution, bandwidth, utilization, frame rate, frame loss, out-of-sequence
frames, in-sequence frames.
Packet jitter statistics Delay variation statistics (ms) — min., max., last, average, jitter measurement estimate.
Flow control injection Packet pause time.
Flow control statistics Pause time, last pause time, max. pause time, min. pause time, paused frames, abort frames, frames Tx, frames Rx.
Advanced auto-negotiation Capability to auto-negotiate the rate, duplex and flow control capabilities with another Ethernet port.
Configurable auto-negociation parameters.
Display of link partner capabilities.
Fault injection: offline, link failure, auto-negotiation error.
Advanced filtering a Capability to enhance the filters with up to four fields each, that can be combined with AND/OR/NOT operations. A mask is also provided
for each field value to allow for wildcards. Complete statistics are gathered for each defined filter.
Through mode a Capability to test in Through/Pass Through mode.
Data capture a Capability to perform 10/100/1000M full-line-rate data capture and decode. Capability to configure detailed capture filters and triggers as
well as capture slicing parameters.
Traffic scan a Capability to scan incoming live traffic and auto-discover all VLAN/VLAN Priority and MPLS ID/COS flows. Capability to provide statistics
for each flow including frame count and bandwidth.