Atec Agilent-34461A - Manual (Page 15)

15
34460A/34461A
O P T I O N S & A C C E S S O R I E S
Accessories
Accessories included
34460A: Power cord
Calibration certifi cate
34461A: 34138A test lead set with probes, fi ne tip probes, SMT grabbers
and mini grabber attachments
Power cord
Documentation CD
IO Libraries CD
USB cable
Calibration certifi cate
Accessories available
11059A Kelvin probe set
11060A Surface-mount device probe
11062A Kelvin clip set
34131A Transit case
34133A Precision electronic test leads
34134A DC-coupled current probe
34136A High-voltage probe
34138A Test lead set
34162A Accessory pouch
34171B Input terminal block
34172B Calibration short
34308A Thermistor kit
34330A 30-A current shunt
E2308A Thermistor temperature probe
Y1133A Low-thermal external digital multimeter scanning kit
Options
34460A Digital multimeter, 6½ digit, basic Truevolt DMM
LAN Rear panel LAN/LXI Web interface, external triggering for 34460A
SEC Enable NISPOM and fi le security for Truevolt Series DMMs
Z54 Certifi cate of calibration – ANSI/NCSL Z540.3-2006, printed
GPB GPIB user-installable interface module for Truevolt Series DMMs
ACC Accessory kit for 34460A – documentation CDs, test leads, USB cable
34461A Digital multimeter, 6½ digit, 34401A replacement, Truevolt DMM
SEC Enable NISPOM and fi le security for Truevolt Series DMMs
Z54 Certifi cate of calibration – ANSI/NCSL Z540.3-2006, printed
GPB GPIB user-installable interface module for Truevolt Series DMMs
Standalone product numbers
Ordered as standalone to be installed by the distributor or customer
3446LANU Upgrade:
Rear panel LAN/LXI Web interface, external triggering for 34460A
3446SECU Upgrade:
Enable NISPOM and fi le security for Truevolt Series DMMs
3446GPBU Upgrade:
GPIB user-installable interface module for Truevolt Series DMMs
3446ACCU Accessory kit for 34460A:
Documentation CDs, test leads, USB cable
Rack mount kits
34190A Rackmount kit:
Use for mounting one 2U instrument by itself, without another instrument
laterally next to it. Includes one rack fl ange and one combination
rack fl ange-fi ller panel.
34191A 2U dual fl ange kit:
Use for mounting two 2U instruments side-by-side.
Includes two standard rack fl anges.
Note: Mounting two instruments side-by-side will require the
34194A dual-lock link kit and a shelf for the instruments to sit on.
34194A Dual lock link kit:
For side-by-side combinations of instruments and includes links
for instruments of different depths.
Defi nitions
Specifi cation (spec)
The warranted performance of a calibrated instrument that has been stored for a
minimum of 2 hours within the operating temperature range of 0 – 55 °C and after a
60-minute warm up period. All specifi cations include measurement uncertainty and
were created in compliance with ISO-17025 methods. Data published in this document
are specifi cations (spec) only where specifi cally indicated.
Typical (typ)
The characteristic performance, which 80% or more of manufactured instruments will
meet. This data is not warranted, does not include measurement uncertainty, and is
valid only at room temperature (approximately 23 °C).
Nominal (nom)
The mean or average characteristic performance, or the value of an attribute that is
determined by design such as a connector type, physical dimension, or operating speed.
This data is not warranted and is measured at room temperature (approximately 23 °C).
Measured (meas)
An attribute measured during development for purposes of communicating the expected
performance. This data is not warranted and is measured at room temperature (ap-
proximately 23 °C).
T
CAL
The temperature at which the instrument was calibrated.
Standard 3-Year Warranty