Remote contr ol, cont’d – Extron Electronics FOX 4G Matrix 7200 Setup Guide User Manual
Page 14
Refer also to the FOX 4G Matrix Switchers User’
s Manual at www
.extron.com.
Refer also to the FOX 4G Matrix Switchers User’
s Manual at www
.extron.com.
Command
ASCII command
(host to switcher)
Response
(switcher to host)
Additional description
Create ties
N
• Commands can be entered back-to-back in a string, with no spaces. For example: 1*1!02*02&003*003%.
• The matrix switchers support 1-, 2-, and 3-digit numeric entries (1*1!, 02*02&, or 003*003%).
N
The ! tie command, the
& tie command, and the % tie command can be used interchangeably.
N
The ! read tie command,
& read tie command, and the % read tie command can be used interchangeably.
Tie input
X!
to output
X@
X!
*
X@
!
Out
X@
•
In
X!
•
All
]
Tie input
X!
to output
X@
.
Example (see Note, above):
1*3!
Out03•In01•All
]
Tie input 1 to output 3.
Tie input
X!
to output
X@
X!
*
X@
&
Out
X@
•
In
X!
•
RGB
]
Tie input
X!
to output
X@
.
Example (see Note, above):
10*4&
Out04•In10•RGB
]
Tie input 10 to output 4.
Tie input
X!
to output
X@
X!
*
X@
%
Out
X@
•
In
X!
•
Vid
]
Tie input
X!
to output
X@
.
Example (see Note, above):
7*5%
Out05•In07•Vid
]
Tie input 7 to output 5.
Read output tie
X@
&
X!]
Input
X!
is tied to output
X@
.
Read output tie
X@
%
X!]
Input
X!
is tied to output
X@
.
Read output tie
X@
!
X!]
Input
X!
is tied to output
X@
.
Command
ASCII command
(host to switcher)
Response
(switcher to host)
Additional description
Channel mute commands
Channel mute
X@
*1B
Vmt
X@
*1
]
Mute output
X@
(no signal is output, but
the light output remains active).
Channel unmute
X@
*0B
Vmt
X@
*0
]
Unmute output
X@
(signal is output).
Read channel mute
X@
B
X#]
1 = mute on, 0 = mute off.
Global channel mute
1*B
Vmt1
]
Mute all light outputs.
Global channel unmute
0*B
Vmt0
]
Unmute all light outputs.
View output mutes
E
VM
}
X#
1
,
X#
2
, ...
X#
n
]
Each
X#
response is the mute status of an
output, starting from output 1.
n
= the maximum number of outputs for
your configuration.
Save and recall presets
N
If you try to recall a preset that is not saved, the matrix switcher responds with the error code
E11.
Save current configuration as a
global preset
X$,
Spr
X$]
Command character is a comma.
Example:
9
,
Spr09
]
Save current ties as preset 9.
Recall a global preset
X$.
Rpr
X$]
Command character is a period.
Example:
5
.
Rpr05
]
Recall preset 5, which becomes the current
configuration.
N
X!
= Input number
00 – (maximum number of inputs for your configuration) (00 = untied)
X@
= Output number
01 – (maximum number of outputs for your configuration)
N
X@
= Output number
01 – (maximum number of outputs for your model)
X#
= Mute
0 = not muted, 1 = muted
X$
= Global or room preset #
00 - 64
FOX 4G Matrix Switchers • Remote Contr
ol
Remote Contr
ol, cont’d
4-4
FOX 4G Matrix Switchers • Remote Contr
ol
4-5