Asus P2B-DS - Manual (Page 11)

ASUS P2B-D/P2B-DS User’s Manual 11
III. INSTALLATION
Jumpers
1) CLRTC p. 13 Clear Real Time Clock (RTC) RAM
2) KBPK p. 13 Keyboard Power Up (Enable/Disable)
3) FS0, FS1, FS2 p. 14 CPU Bus Frequency
4) BF0, BF1, BF2, BF3 p. 14 CPU Core:Bus Frequency Multiple
5) JP18 p. 15 Chassis Intrusion Sensor Setting (Enable/Disable)
Expansion Slots/Sockets
1) DIMM Sockets p. 18 DIMM Memory Support
2) SEC CPU Slot p. 19 Single Edge Contact CPU Support
3) SLOT1, SLOT2 p. 24 16-bit ISA Bus Expansion Slots *
4) PCI1, PCI2, PCI3, PCI4 p. 25 32-bit PCI Bus Expansion Slots †
5) AGP p. 25 Accelerated Graphics Port
Hardware Monitor
1) JP4, JP5 p. 23 CPU heat Sensor Connector (O/R)
Connectors
1) PS2KBMS p. 26 PS/2 Keyboard Connector (6-pin female)
2) PS2KBMS p. 26 PS/2 Mouse Connector (6-pin female)
3) PRINTER p. 27 Parallel (Printer) Port Connector (25-pin female)
4) COM1/COM2 p. 27 Serial Port COM1/COM2 (two 9-pin male)
5) FLOPPY p. 27 Floppy Drive Connector (34-1 pins)
6) USB p. 28 Universal Serial BUS Ports 1 & 2 (two 4-pin female)
7) Primary/Secondary IDE p. 28 Primary/Secondary IDE Connector (40 pins)
8) IDELED p. 29 IDE/SCSI LED Activity Light (2 pins)
9) CHA_/CPU_/PWR_FAN p. 29 Chassis/CPU/Power Supply Fan Connectors (3-pin block)
10) IR p. 30 Infrared Port Module Connector (5 pins)
11) ATXPWR p. 30 ATX Motherboard Power Connector (20 pins)
12) WOLCON p. 31 Wake-On-LAN Connector (3 pins)
13) CHASSIS p. 31 Chassis Intrusion Sensor Lead (4-1 pins) (O/R)
14) MSG.LED (PANEL) p. 32 LED Lead (2 pins)
15) SMI (PANEL) p. 32 SMI Suspend Switch Lead (2 pins)
16) PWR.SW (PANEL) p. 32 ATX Power Switch / Soft Power Switch (2 pins)
17) RESET (PANEL) p. 32 Reset Switch Lead (2 pins)
18) PWR.LED (PANEL) p. 32 System Power LED (3 pins)
19) KEYLOCK (PANEL) p. 32 Keyboard Lock Switch Lead (2 pins)
20) SPEAKER (PANEL) p. 32 Speaker Connector (4 pins)
21) SCSI-50/SCSI-68/ULTRA2-68 p. 33 Ultra-Fast (50-)/-Wide (68-)/Ultra2 (68-pin) SCSI Connectors
22) DMA_HEADER
p. 34 SB-LINK™ Connector (6-1 pins) (O/R)
23) SMB p. 34 SMBus Connector (3 pins) (O/R)
Layout Contents
III. INST
ALLA
TION
* The onboard hardware monitor uses the address 290H-297H so legacy ISA cards must not use this
address, otherwise conflicts will occur.
O/R: Optional/Reserved for future use.