Derale Performance High Amperage Adjustable Single Electric Fan Controller, 3__8" NPT Thread In Probe - Manual

16779-InstructionSheet
Derale Performance, Los Angeles, CA 800.421.6288 www.derale.com
INSTALLATION INSTRUCTIONS
ADJUSTABLE SINGLE ELECTRIC FAN CONTROLLER
PART # 16779
KIT CONTENTS
Please read these instructions completely before beginning installation
TOOLS NEEDED
Drill
5/32” Drill Bit
Teflon Tape
12V Test Light
Standard Screw Driver
or a 5/16” Nut Driver
Standard Screw Driver
(1/8” wide blade)
Wire Stripper
Wire Crimping Tool
3/4” Open End Wrench
CONTROL MODULE INSTALLATION
1. Choose a convenient location, preferably along the vehicles core
support near the battery. Take in to consideration probe placement &
wire routing requirements. Avoid mounting near HOT engine
components or a location that would be in direct contact with any road
debris.
2. Using the module as a template, mark and drill four 5/32” holes in the
proper location.
3. Using four #10 sheet metal screws supplied, secure the unit in place.
CIRCUIT BREAKER MOUNTING
1. Choose a convenient location for the Circuit Breaker that is between
the Fan Controller and the Battery.
2. Using the breaker as a template, mark and drill two 5/32” holes in the
proper locations.
3. Using the remaining two #10 sheet metal screws supplied, secure the
Circuit Breaker in place.
THERMOSTAT PROBE INSTALLATION (See Diagram #2)
Placement
1. Locate a 3/8” NPT water jacket port either on the radiator, waterneck,
intake manifold or cylinder heads.
Installation
1. Using Teflon Tape or suitable sealant, thread the 3/8” NPT probe into
the desired port. Be careful not to over tighten.
Note: Probe wires can be lengthened if necessary. When lengthening wires
always use good quality wire & connections to assure proper function.
3/8” NPT
Brass Probe
3/8” NPT
Brass Probe
Diagram #2
WIRING
Before starting, disconnect the Negative (-) cable on the vehicles battery.
Using the electrical connectors and wire ties provided, follow the instructions below. (See Diagram #3 on reverse side)
Red Wire (harness side): To Positive (+) 12v Battery
1. Using the Yellow 5/16” Ring Terminal & 10 Ga. Red Wire supplied, connect one end of the red wire to the vehicles Positive (+)
terminal on the battery.
2. Route the 10 Ga. Red Wire now connected to the battery to the Circuit Breaker previously installed and cut the wire to the
appropriate length.
3. Using a Yellow #10 Ring Terminal, connect the 10 Ga. Red Wire to the “BAT” Terminal on the Circuit Breaker.
This unit utilizes an auto resetting circuit breaker to protect the fan
and controller circuit. In the event of an electrical short, the breaker
will “trip” and open the connection between the battery and the
controller. If this happens, turn the vehicle off and let it cool before
restarting the system. The breaker will automatically reset.
IMPORTANT WARNING
This unit is designed to control one electric fan with
a Maximum Draw of 35 Continuous Amps.
For proper installation the control module must be
mounted within 5 feet of the vehicle's battery.
(Wiring Continues on reverse side)
Diagram #1
Rubber
Plug
Probe Wires
Battery (+)
Override (+)
Adjustment
Screw
Ground (-)
Fan 1 (+)
QTY. DESCRIPTION
1 Adjustable Fan Controller
with 3/8” NPT Thread-in Probe
1 25 Amp Circuit Breaker
1 5ft 10 Ga. Red Wire
6 #10 Sheet Metal Screw
QTY. DESCRIPTION
3 Yellow Butt Connector
2 Yellow #10 Ring Terminal
1 Yellow 5/16” Ring Terminal
2 Blue Wire Tap Connector
4 4” Wire Ties
Ignition (+)
Rev. 08132013