beautypg.com

Rough Country 862 User Manual

Nissan 04 –up titan 3” suspension kit

background image

Nissan 04 –up Titan 3” Suspension Kit

Thank you for choosing Rough Country for all your suspension needs.


Rough Country recommends a certified technician install this system. In addition to these instructions, professional
knowledge of disassemble/reassembly procedures as well as post installation checks must be known. Attempts to install
this system without this knowledge and expertise may jeopardize the integrity and/or operating safety of the vehicle.

Please read instructions before beginning installation. Check the kit hardware against the parts list. Be sure you have
all needed parts and know where they go. Also please review the tool list and make sure you have the necessary tools
to install the kit.

PRODUCT USE INFORMATION

As a general rule, the taller a vehicle is, the easier it will roll. We strongly recommend, because of rollover possibility, that
seat belts and shoulder harnesses should be worn at all times. Avoid situations where a side rollover may occur. Gener-
ally, braking performance and capability are decreased when larger/heavier tires and wheels are used. Take this into
consideration while driving. Do not add, alter, or fabricate any factory or after-market parts to increase vehicle height
over the intended height of the Rough Country product purchased. Mixing component brands is not recommended.

Rough Country makes no claims regarding lifting devices and excludes any and all implied claims. We will not be re-
sponsible for any product that is altered.

We will be happy to answer any questions concerning the design, function, and

correct use of our products.

This suspension system was developed using a

33X12.50/17, tire with factory wheels. The lift was designed as a level-

ing kit only.

NOTICE TO DEALER AND VEHICLE OWNER

Any vehicle equipped with any Rough Country product should have a

“Warning to Driver” decal installed on the inside of

the windshield or on the vehicle

’s dash. The decal should act as a constant reminder for whoever is operating the vehi-

cle of its unique handling characteristics. It is your responsibility to install the warning decal and forward these installation
instructions on to the vehicle owner for review. These instructions should be kept in the vehicle for its service life.

On 2011 & 2012 models, the vehicle was equipped from the factory with a 4 1/2” diameter driveshaft at the u-

joint. As a stock un-lifted vehicle, this oversize shaft coupled with the lack of adequate clearance with the floor

pan from the factory, may cause the shaft to contact with the floor pan. This kit does not minimize the clearance

in this area but is usually recognized with the addition of larger tires and aggressive power-train torque both in

on road and off road situations. If contact does occur, modification of the floor pan may be needed to gain clear-

ance on the oversize driveshaft. This is accomplished by creating more space between the driveshaft and the

floor pan by manipulation of the body pan directly above and to the side of the u-joint on the driveshaft.

Tools Needed:

19 mm Socket
13/16

” Socket

22 mm Socket
Hammer
17 mm Wrench
14 mm Socket
18mm Wrench
19 mm Wrench
Grinder

9286200

Kit Contents:

2-Front Strut Extensions

1-Driver Side Control Arm

1-Pass Side Control Arm

2-Sway Bar Links

1-3/8” Bag containing:

6-3/8

” x 1 1/2”studs

6-3/8

” Nuts

6-3/8

” Lock Washers


1-862BAG4 Sway Bar link Bag:

4-12mm x 65mm Bolts

4-12mm Flange Lock nuts

4-12mm ID sleeves

2-Flat Washers

Torque Specs:

Size Grade 5 Grade 8
5/16

” 15 ft/lbs 20 ft/lbs

3/8

” 30 ft/lbs 35 ft/lbs

9/16

” 95 ft/lbs 130 ft/lbs

5/8

” 135 ft/lbs 175 ft/lbs

3/4

” 185 ft/lbs 280 ft/lbs


Class 8.8

Class 10.9

10MM

32ft/lbs

45ft/lbs

12MM

55ft/lbs

75ft/lbs

14MM

85ft/lbs

120ft/lbs

16MM

130ft/lbs

165ft/lbs

18MM

170ft/lbs

240ft/lbs