Toner Cable EN-20 HD_SD Dual SDI MPEG2 Encoder with QAM Modulator - Manual (Page 2)

EN-20
HD / SD Dual SDI MPEG2 Encoder
with QAM Modulator
Specifications Subject To Change Without Notice Rev 06-12 ©Toner Cable Equipment, Inc.
969 Horsham Road l Horsham, Pennsylvania 19044 USA l Phone: 215-675-2053 Fax: 215-675-7543 l [email protected]
Encoder Video Profiles
MPEG 2 SD Profile 1: Adaptive Field Frame (AFF) ISO13818-2 MP@ML
MPEG 2 SD Profile 2: AFF ISO13818-2 422P@ML
MPEG 2 HD Profile 2: ISO13818-2 MP@HL (1920 x 1080 or 1280 x 720)
Video Encoding Data Rates (Manual)
MPEG 2 MP@ML SD / 1 Mbs-15 Mbs - NTSC and PAL
MPEG 2 422P@ML SD / 1 Mbs-50 Mbs - NTSC and PALMPEG 2 MP@HL / 7
Mbs-59.5 Mbs
Video Encoding Data Rates (Automatic based on QAM Configuration)
720 P: 12-23 Mbs1080i: 14-25 MbsNTSC/PAL: 15Mbs fixed(HD rates are
calculated based on video input resolution, video complexity and QAM target)
Video Input:
Connector: BNC 75 Ohm
Interface: SD/HD-SDI Auto frame rate and resolution detection
SD-SDI (SMPTE 259M - 270 Mbit/s) with embedded audio per SMPTE
272MHD-SDI (SMPTE 272M - 1.485 Gbit/s) with embedded audio per SMPTE
299M
Connector: BNC 75 Ohmz
Interface: SD Composite (CVBS)
Analog Composite NTSC and PAL
Audio Input:
Connector/Interface:BNC/SDI, RCA/SPDIF (Synchronous to video) and
DB9/Analog
Supported Audio: (single audio pair per video encoder in two-channel mode)
Dolby Digital 2.0 (AC3) encode
MPEG1 Layer 2 encode
Dolby E passthrough
Dolby 5.1 passthrough
Dolby Digital 2.0 (AC3) passthrough
Analog Digital/Closed Captions/VBI VANC
Waveform or Analog (Composite or SD-SDI):
Connector: RCA jack 75 Ohm Terminated Input
Closed Captions per CEA-608-C (2005), Closed Captions per DVS-157, Wide
Screen Signaling (WSS) per ETSI EN300294 V1.4.1 (2003-04), Teletext per
ETSI EN 300 472 V1.3.1 (2003-05)
Ancillary (ANC) per SMPTE 291M (Native via SD/HD-SDI):
Connector: BNC 75 Ohm Terminated Input for HD/SD-SDI
Closed Captions per CEA-708 (SMPTE 291M), Teletext per OP47 and SMPTE
2031, VITC per
SMPTE 2038, EBU Teletext/Subtitles, WSS/Teletext/NABTS/CEA-
608/TV2GX/AMOL48/96, User Defined (2031-2007) per SMPTE 2031,
AFD/Bar Data/Pan Scan per CEA-CEB16 (2006) per SMPTE 2016
Waveform Bridging and Conversion of Video User Data
Connector: BNC 75 Ohm Terminated Input
CEA 608 to CEA 708 up-conversion
Caption Bridging: CEA-608 via Composite merged with SD or HD Video via
SDI (Similar frame rates required)
Teletext Bridging: Waveform Teletext via Composite merged with SD or HD
Video via SDI
WSS Bridging: Waveform WSS via Composite merged with SD Video via SDI
Transport Stream User Data Carriage
SCTE 127-2007, ETSI EN 301 775, v1.2.1 (2003-05)
Emergency Alert System (EAS) Input:
EAS Video:
Connector: RCA jack 75Ohm
Interface: Terminated NTSC or PAL D1 Composite Input with loop
EAS Audio:
Connector: Vertical single RCA jack
Interface: mono audio channel with loop
EAS Triggering Interface:
GPIWeb UIXCP
Conditional Access:
BISS 1/E option
Transport Outputs:
All outputs operate concurrently.
ASI
Connector: BNC x2
ISO13818-1 MPEG 2 Transport Stream per EN 50083-9:1997 (188 byte only).
Physical interface 72 Mbit/s.
Transport Over IP (TSoIP)
Connector: RJ45 x1
ISO13818-1 MPEG 2 Transport Stream per EN 50083-9:1997 (188 byte only).
UDP or RTP encapsulated routes with SMPTE 2022 (COP3 FEC). MPTS or SPTS user defin-
able.
QAM
Connector: F-style RF female jack
Frequency: 50 to 862 Mhz
QAM Modulation Schemes supported:
Annex A (8 Mhz)
Annex B (6 Mhz)
QAM constellations:
Annex A: 64, 256
Annex B: 64, 256
Main Power: 45dBmV to 56dBmV, in 1 dBmV increments
MER: 38.0 dB minimum (average).
IF Output Connector: F-style RF female/jack Frequency: Selectable 44 MHz
(USA) and 36.125MHz (Europe)
Physical:
Operating Temp.: 0 to +50 °C/+32 to +122°F
Power Supply (nominal): 100 - 240 VAC
Power Consumption (nominal): 33.6 W (120V @ 280mA)
Weight: 6 lbs
Measurements: (H X W X D) 1.73” X 19” X 13.32”
Managment:
Front Panel Controls
Browser-based Web Interface
SNMP
Specifications