Trek PD07016 High-Voltage Power Amplifier - Manual (Page 2)

Features (cont.)
High-Voltage On/Off
Local Individual push-button switches
Remote TTL compatible input. TTL high (or open) turns
off high-voltage output. TTL low turns on high-
voltage output.
Current Limit/Trip Switch selectable for limit or trip. Graduated 1-
turn panel potentiometer is used to adjust limit
or trip level from 0 to ±60 mA.
Out of Regulation
Status Indicator and
Connector Illuminates and TTL low is provided when unit
fails to produce required HV output such as
during current limit.
Limit/Trip Status
Indicator and
Connector Illuminates and a TTL low is provided when HV
is disabled or when amplifier is out of regulation
for more than 500 ms
Mechanical
Dimensions 91.4 cm H x 43 cm W x 87 cm D
(36” H x 17” W x 34” D) Depth dimension
includes handles and spacing for air flow.
Weight 73 kg (160 lb) approximate
HV Connector Caton high-voltage Connector
BNC Connectors Amplifier Input, Voltage Monitor, Current Monitor,
Remote High Voltage ON/OFF, Out of Regulation
Status, Fault/Trip Status
Operating Conditions
Temperature 0°C to 40°C (32°F to 104°F)
Relative Humidity To 75%, noncondensing
Altitude To 1524 meters (5000 ft.)
Electrical
Line Voltage Factory set for one of two ranges:
104 to 127 V AC or 180 to 250 V AC at 48 to
63 Hz (specify when ordering)
Power Consumption 1800 VA, maximum
AC Line Receptacle Standard 3-prong with integral fuse holder
Supplied Accessories
Operators Manual PN: 23383
Shorting BNC Cap PN: B3060
HV Output Cable PN: 43466
Line Cord, Fuses Selected per geographic destination
Optional Accessories
Locking Wheel Kit CN: 1K042
Model PD07016 Specifications
Performance
Output Voltage
Range 0 to ±10 kV DC or peak AC
Output Current
Range 0 to ±60 mA DC, 0 to 300 mA peak capability
for 20 µs
Input Voltage Range 0 to ±10 V DC or peak AC
Input Impedance 25 kW nominal (inverting/differential option
50 kW, nominal)
DC Voltage Gain 1000 V/V
DC Voltage Gain
Accuracy Better than 0.1% of full scale
Offset Voltage Less than ±4 V
Output Noise Less than 5 V rms*
Slew Rate
(10% to 90%, typical) Greater than 1000 V/µs
Small Signal
Bandwidth (-3dB) DC to greater than 20 kHz
Large Signal
Bandwidth
(2% distortion) DC to greater than 10 kHz
Stability
Drift with Time Less than 50 ppm/hr, noncumulative
Drift with
Temperature -
Less than 100 ppm/°C
Voltage Monitor
Ratio 1 V / 1000 V
DC Accuracy Better than 0.1% of full scale
DC Offset Voltage Less than ±5 mV
Output Noise Less than 20 mV rms*
Output Impedance 47 W
Current Monitor
Ratio 30 V/mA
DC Accuracy Better than 2% of full scale
Offset Voltage Less than ±10 mV
Output Noise Less than 30 mV rms*
Bandwidth (-3dB) DC to greater than 5 kHz
Output Impedance 47 W
Features
Settling Time (to 1%) Less than 200 µs for a 0 to 10 kV step
Dynamic Adjustment Graduated 1-turn panel potentiometer is used
to optimize the AC response for various load
parameters.
Copyright ã 2012 TREK, INC. All specifications are subject to change. 1236/DEC *Measured using the true rms feature of the Hewlett Packard Model 34401A digital multimeter
Measurement and Power Solutions TM