Altronix AL400UL3X Installation Instructions - Manual (Page 2)

- 2 - AL400UL3/AL400UL3X
Overview:
The AL400UL3/AL400UL3X multi-output power supply/charger is specifically designed for use with access control,
burglar alarm, fire and nurse call systems and accessories. The AL400UL3/AL400UL3X converts a 115VAC 60Hz input
into three (3) individually regulated power-limited outputs (see specifications).
Specifications:
Stand-by Specifications (total current shown)*:
Output
4 hr. of Stand-by &
5 Minutes of Alarm
24 hr. of Stand-by &
5 Minutes of Alarm
60 hr. of Stand-by &
5 Minutes of Alarm
24VDC / 12AH Battery --------
Stand-by = 200mA
Alarm = 3.0 amp
--------
24VDC / 40AH Battery
Stand-by = 3.0 amp
Alarm = 3.0 amp
Stand-by = 1.0 amp
Alarm = 3.0 amp
Stand-by = 300mA
Alarm = 3.0 amp
*Current is measured between power supply and ALX3B board.
Installation Instructions:
Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/NFPA 72/ANSI, and with all local
codes and authorities having jurisdiction. Product is intended for indoor use only.
1. Mount unit in the desired location. Mark and predrill holes in the wall to line up with the top two keyholes in the
enclosure. Install two upper fasteners and screws in the wall with the screw heads protruding. Place the enclosure’s
upper keyholes over the two upper screws, level and secure. Mark the position of the lower two holes. Remove the
enclosure. Drill the lower holes and install the three fasteners. Place the enclosure’s upper keyholes over the two
upper screws. Install the two lower screws and make sure to tighten all screws (Enclosure Dimensions, pgs. 6-7).
Secure enclosure to earth ground. It is recommended to first review the following tables for screw terminals, switch
selection and LED status indications. This will greatly facilitate installation hook-up.
Carefully review:
Stand-by Specifications
(pg. 2)
LED Diagnostics (pg. 4)
Terminal Identification Table (pg. 4)
Agency Listings:
• UL Listed for Access Control System Units
(UL 294), UL Listed for Power Supplies for Use with
Burglar-Alarm Systems (UL 603), UL Listed Hospital
Signaling and Nurse Call Equipment (UL 1069) and
UL Listed Standard for Safety for Fire Protective
Signaling Systems (UL 1481).
• MEA - NYC Department of Buildings Approved.
• CSFM - California State Fire Marshal Approved.
• NFPA 72 Compliant (Fire-Protective Signaling Service).
Input:
• Input 115VAC / 60Hz, 3.5 amp.
• Input fuse rated @ 5A/250V.
Output:
• Class 2 Rated power-limited output(s).
• 1.75 amp continuous supply current at 5VDC.
• 1.75 amp continuous supply current at 12VDC.
• 1.5 amp continuous supply current at 24VDC.
Burglar Alarm Applications (UL 603):
12VDC = 10VDC-13.2VDC.
24VDC = 20VDC-26.4VDC.
• 100 mV p/p output ripple.
Output (cont’d.):
• Short circuit and thermal overload protection.
• Output fuse rated at 15A/32V.
Battery Backup
• Built-in charger for sealed lead acid or gel type batteries.
• Automatic switch over to stand-by battery when
AC fails.
• Maximum charge current 0.7 amp.
• Zero voltage drop when switched over to battery backup.
Supervision:
• AC fail supervision (form “C” contacts).
• Low battery and battery presence supervision
(form “C” contacts).
Additional Features:
• Power supply, enclosure, cam lock and battery leads.
• AC input and DC output LED indicators.
Enclosure dimensions (HxWxD):
AL400UL3 - accommodates up to two (2)
12VDC/7AH batteries.
13.5” x 13” x 3.25” (342.9mm x 330.2mm x 82.55mm)
AL400UL3X - accommodates up to two (2)
12VDC/12AH batteries
15.5” x 12” x 4.5” (393.7mm x 304.8mm x 114.3mm)