Altronix AL600UL3 Installation Instructions - Manual (Page 2)

- 2 - AL600UL3/AL600UL3X
Overview:
The AL600UL3/AL600UL3X Triple Output Power Supply/Charger is specifically designed for use with access control
and fire-protective signaling systems and accessories. The AL600UL3/AL600UL3X converts a 115VAC 60Hz input into
three (3) outputs (see specifications).
Specifications:
Stand-by Specifications (Current is specified on AL3XB input):
Output
4 hr. of Stand-by &
5 Minutes of Alarm
24 hr. of Stand-by &
5 Minutes of Alarm
60 hr. of Stand-by &
5 Minutes of Alarm
24VDC / 40AH Battery
5VDC - 1.75 amp 5VDC - 0.3 amp 5VDC - 0.1 amp
12VDC - 1.75 amp 12VDC - 0.3 amp 12VDC - 0.1 amp
24VDC - 3 amp 24VDC - 0.3 amp 24VDC - 0.1 amp
Installation Instructions:
Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/NFPA 72/ANSI, and with all local
codes and authorities having jurisdiction. Product is intended for indoor use only.
1. Mount unit in desired location. Mark and predrill holes in the wall to line up with the top two keyholes in the
enclosure. Install two upper fasteners and screws in the wall with the screw heads protruding. Place the enclosure’s
upper keyholes over the two upper screws, level and secure. Mark the position of the lower two holes. Remove the
enclosure. Drill the lower holes and install the three fasteners. Place the enclosure’s upper keyholes over the two
upper screws. Install the two lower screws and make sure to tighten all screws (Enclosure Dimensions, pgs. 7-8).
Secure enclosure to earth ground. It is recommended to first review the following tables for screw terminals, switch
selection and LED status indications. This will greatly facilitate installation hook-up.
Carefully review:
Stand-by Specifications
(pg. 2)
LED Diagnostics (pg. 4)
Terminal Identification Table (pg. 4)
2. Connect AC power (115VAC 60Hz to terminals marked [L, N] (Fig. 1, pg. 3). Use 14 AWG or larger for all power
connections (Battery, DC output, AC input). Use 22 AWG to 18 AWG for power-limited circuits
(AC Fail/Low Battery reporting).
Keep power-limited wiring separate from non power-limited wiring (115VAC / 60Hz Input, Battery Wires).
Minimum 0.25” spacing must be provided.
For Fire Alarm applications the outputs are “Special Applications” only, see list (refer to Appendix A, pg. 5).
3. Measure output voltage before connecting devices. This helps avoid potential damage.
Agency Listings:
• UL Listed for Access Control System Units
(UL 294) and UL Listed Standard
for Safety for Fire Protective Signaling Systems
(UL 1481).
• MEA - NYC Department of Buildings Approved.
• CSFM - California State Fire Marshal Approved.
• NFPA 72 compliant (Fire-Protective Signaling Service).
Input:
• Input 115VAC / 60Hz, 3.5 amp.
• AC input and DC output LED indicators.
Output:
• Class 2 Rated power-limited outputs
(5VDC and 12VDC only).
• 1.75 amp continuous supply current at
5VDC and 12VDC regulated outputs.
• 3 amp continuous supply current at 24VDC
(for Fire-Protective Signaling use Special applications).
• Filtered and electronically regulated outputs.
100 mV p/p output ripple.
Output (cont’d.):
• Short circuit and thermal overload protection.
Battery Backup
• Built-in charger for sealed lead acid or gel type batteries.
• Automatic switch over to stand-by battery when
AC fails.
• Maximum charge current 0.7 amp.
• Zero voltage drop when switched over to battery backup.
Supervision:
• AC fail supervision (form “C” contacts).
• Low battery and battery presence supervision
(form “C” contacts).
Additional Features:
• Power supply, enclosure, cam lock and battery leads.
• Enclosure accommodates up to two (2) 7AH batteries.
Enclosure dimensions (HxWxD):
AL600UL3
13.5” (342.9mm) x 13” (330.2mm) x 3.25” (82.55mm)
AL600UL3X
15.5” (393.7mm) x 12” (304.8mm) x 4.5” (114.3mm)