Ohaus DEFENDER 5000 BENCH SCALES Manual en - Manual (Page 51)

EN-49 5000 Series Indicators
5.2 Output Format
5.3 Printouts
The following sample print outs are generated by the Print button, “P” Command or alternate print command. The content of the
printout is defined in the Print Content menu item. A maximum of 24 characters can be printed on each line.
NOTE: Shaded areas = this date is printed when set on in the Print Content menu.
Unshaded = typical
Weigh Mode Printout Count Mode Printout Percent Mode Printout
O h a u s C o r p o r a t i o n O h a u s C o r p o r a t i o n O h a u s C o r p o r a t i o n
1 9 A C h a p i n R o a d 1 9 A C h a p i n R o a d 1 9 A C h a p i n R o a d
P . O . B o x 2 0 3 3 P . O . B o x 2 0 3 3 P . O . B o x 2 0 3 3
P i n e B r o o k , N J , 0 7 0 5 8 U S A P i n e B r o o k , N J , 0 7 0 5 8 U S A P i n e B r o o k , N J , 0 7 0 5 8 U S A
T e l : + 1 - 9 7 3 - 3 7 7 - 9 0 0 0 T e l : + 1 - 9 7 3 - 3 7 7 - 9 0 0 0 T e l : + 1 - 9 7 3 - 3 7 7 - 9 0 0 0
0 1 / 3 1 / 0 8 1 2 : 3 0 P M 0 1 / 3 1 / 0 8 1 2 : 3 0 P M 0 1 / 3 1 / 0 8 1 2 : 3 0 P M
S c a l e I D : 1 2 3 4 5 6 S c a l e I D : 1 2 3 4 5 6 S c a l e I D : 1 2 3 4 5 6
U s e r I D : 1 2 3 4 5 6 U s e r I D : 1 2 3 4 5 6 U s e r I D : 1 2 3 4 5 6
P r o j e c t I D : 1 2 3 4 5 6 P r o j e c t I D : 1 2 3 4 5 6 P r o j e c t I D : 1 2 3 4 5 6
N a m e : _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ N a m e : _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ N a m e : _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
1 0 . 0 0 k g N Q u a n t i t y : 1 0 0 P C S P e r c e n t a g e : 1 0 %
1 1 . 0 0 k g G 1 1 . 0 0 k g G 1 1 . 0 0 k g G
1 0 . 0 0 k g N 1 0 . 0 0 k g N 1 0 . 0 0 k g N
1 . 0 0 k g T 1 . 0 0 k g T 1 . 0 0 k g T
M o d e : W e i g h A P W 0 . 1 0 0 0 k g R e f . W t . 1 0 0 . 0 0 k g
M o d e : C o u n t M o d e : P e r c e n t
*Each field is followed by a single delimiting space (ASCII: 32)
Definitions:
Weight - up to 9 characters, right justified, “-” at immediate left of most significant character (if negative).
Unit - The Unit field contains the unit of measure abbrevation in 5 characters, left justified.
Stability - “?” character is printed if not stable. If weight is stable, a space will be printed instead.
G/N - “N” printed if weight is net weight, “G”, “B”, or a space (depending on GROSS menu setting - Sec. 3.5.7)
printed if weight is a gross weight.
**Terminating Character(s) - terminating character(s) printed depending on FEED menu setting (CR, LF / 4xCR, LF /
ASCII: 12, refer also to Sec. 3.9.5.).
NOTE: If the Print Content – Result menu is set to Numeric Only, the Result output only includes the weight field and the
termination characters.
The default serial output format is shown below.
Field: Weight Space* Unit Space* Stability Space* G/N Space* Term. Char(s)
Length: 9 1 5 1 1 1 1 1 **