Bosch PPR 250 - Manual (Page 17)

English | 17
Bosch Power Tools 2 609 005 736 | (16.1.12)
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under “Technical Data” is in conformity with the fol-
lowing standards or standardization documents: EN 60335,
EN 300 220-1:2006, EN 300 220-2:2007, EN 301 489-
1:2008, EN 301 489-3:2002 according to the provisions of
the directives 2011/65/EU, 2006/95/EC, 2004/108/EC,
1999/5/EC.
11
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
Leinfelden, 26.09.2011
Assembly
f Before any work on the machine itself, pull the mains
plug.
Unreel the Feed Hose (see figure A)
– Open holding clamp 21 and completely unreel feed hose 2
from base unit 5.
– Lock holding clamp 21 again.
Note: When painting only with the paint applicator 3 (without
extension 1), the feed hose 2 can be fastened in one of the
two exterior guide grooves 12 for more convenient working.
Mounting the Extension (see figures B1 – B2)
– Screw the screw connection 10 of the extension into the
paint applicator 3.
– Fasten feed hose 2 in the straight guide grooves 12 of
paint applicator 3 and extension 1.
– Remove remote control 8 from paint applicator 3 and clip
it into holder 6 of extension 1.
Operation
f Before any work on the machine itself, pull the mains
plug.
Preparing for Operation
f Working close to the edge of open waters or on neigh-
bouring areas in the direct vicinity of open waters is not
permitted.
When purchasing paint, observe its environmental compati-
bility.
Preparing the Surface to be Painted
The surface to be painted must be clean, dry and free of
grease.
When working indoors, all non-covered surface can be soiled.
Therefore, thoroughly prepare the area around the surface to
be painted:
– Cover or mask off floors, furnishings, door and window
frames, etc.
– Also, sufficiently underlay the paint bucket and base unit
with covering-off material (foil, cardboard, etc.).
Preparing the Paint
– Prepare the paint according to the manufacturer’s instruc-
tions.
– Stir paint thoroughly and dilute as required.
When the painting result is not satisfactory or no paint comes
out: See “Correction of Malfunctions”, page 18.
Coupling the Base Unit and the Paint Bucket
(see figures C1–C2)
– Set down base unit 5 level on the floor next to the opened
paint bucket.
– Pull the height-adjustable paint-bucket coupling 29 up-
ward to the stop.
– Hold the paint bucket handle upright and slide the hooks of
the paint-bucket coupling down to the edge of the paint
bucket.
The paint bucket handle must always be positioned be-
tween the hooks of the paint-bucket coupling.
– Insert the paint filter 22 to the bottom of the paint bucket.
– Fasten the intake hose 4 in the holding clip 28.
Starting Operation
f Observe correct mains voltage! The voltage of the pow-
er source must agree with the voltage specified on the
nameplate of the machine. Power tools marked with
230 V can also be operated with 220 V.
f Always place the base unit and the paint bucket on a
level surface. When operating the paint roller on a ladder
or an inclined surface, the base unit and the paint bucket
can tip over or fall down. This can lead to injury and con-
tamination from the coating material.
f Do not cover off the base unit. Otherwise, a possible mal-
function cannot be detected.
f Keep other electrical machines/devices away while us-
ing the paint roller or cover them off adequately. Possi-
bly occurring paint splashes can lead to accidents and soil-
ing.
f Regularly provide for proper ventilation in the working
range and for sufficient fresh air throughout the com-
plete area.
f Wear safety glasses/goggles. This will protect your eyes
against splashing or ejected paint.
Wear appropriate work clothes. Paint is difficult to remove
from clothing.
Prevent the hose system from being constricted, e. g.,
through crushing, kinking or pulling! Do not stand on the feed
hose 2.
Keep the hose system away from heat sources.
Do not pull the hoses. Especially when moving the base unit,
do not pull it by the feed hose 2. Carry the base unit only by
the carrying handle 19.
Dr. Egbert Schneider
Senior Vice President
Engineering
Dr. Eckerhard Strötgen
Engineering Director
PT/ESI
OBJ_BUCH-1513-003.book Page 17 Monday, January 16, 2012 11:29 AM