ROWENTA MASTER VALET IS6300 - Manual (Page 21)

16
handle while the panel is rolling back to the top.
WARNING: never let go of the handle until the panel has totally rolled back.
Once the appliance is switched off, it is recommended to wait several minutes so that the
Roll & Press panel has dried before rolling it back.
UК
“«МЮК>˜`ÊÀˆ˜ÃiÊÌ iÊÜ>ÌiÀÊÌ>˜ŽÊi>V Ê̈“iÊLivœÀiÊÃ̜À>}iКˆ˜КœА`iÀÊ̜ÊyÕÃ КœХМК>˜ÞÊÃV>iÊ
particles (fig. 22).
UʜœГiЮКЬˆ˜`КХ«КМ iКiiVÌÀˆV>КVœА`К>˜`ÊVœÃiÊÜˆМ КМ iК6iVАœКГМАˆ«]КМ i˜Ê >˜}ʈÌÊvÀœ“ÊÌ iКVˆ«К
on the pole (fig.23 - fig. 24).
UКœК˜œМКV>ААЮКМ iÊÃÌi>“iÀÊLÞÊÌ iÊÜ>ÌiÀÊÌ>˜ŽÊ >˜`i°К/ ˆГК>««ˆ>˜Viʈ˜VÕ`iГКХ}}>}iÊÃÌޏiÊ
wheels for added convenience when transporting.
WARNING: Never touch the head until it has cooled down completely.
£КUК/А>˜Г«œАМ
UК9œХАК>««ˆ>˜ViʈÃÊwÌÌi`КЬˆМ КМЬœКЬ iiÃÊvœÀÊi>ÃiʜvÊÌÀ>˜Г«œАМ°К/ˆМКМ iК>««ˆ>˜ViÊ̜Ü>А`ГКМ iК
rear holding the pole and then pull along to transport.
UÊ9œÕÊV>˜Ê>ГœКˆvÌÊÕ«ÊÌ iÊ>««ˆ>˜ViКˆ˜КœА`iÀÊ̜ÊÌÀ>˜Г«œАМКˆМ]К>}>ˆ˜К œ`ˆ˜}КМ iК>««ˆ>˜ViÊLÞÊ
the pole.
Do not attempt to lift up or transport the appliance holding the Roll & Press panel, the pedal,
the water tank handle or the built-in hanger. Always roll back the Roll & Press panel before
transporting the appliance. Always make sure the pole is firmly attached to the base unit
before lifting up the appliance (see assembly instructions).
ÓÊUʏi>˜ˆ˜}
Uʏi>˜ÊÌ iʓ>ˆ˜К՘ˆМКЬˆМ К>Ê`>“«КVœМ °К
UКi>˜ÊÌ iÊ,œÊEÊ*ÀiÃÃÊÃÞÃÌi“Ê«>˜iКЬˆМ К>Ê`>“«КVœМ КœАʘœ˜К>LÀ>ÈÛiÊ뜘}i°Ê
Do not use any cleaning products such as soap or detergents.
UКЬ>ÞÃÊ >˜`Ü>Г КМ iК`iˆV>ÌiÃÊÃÌi>“ÊV>«Ê>˜`ÊÜ>ˆМКХ˜МˆКˆМКˆГКМœМ>ÞÊ`ÀÞÊLivœÀiÊÕȘ}Ê>}>ˆ˜°
UК/œК“>ˆ˜Ì>ˆ˜Ê“>Эˆ“Х“К«iАvœА“>˜Vi]ÊޜÕÀÊÃÌi>“iÀʓÕÃÌÊLiÊ`iÃV>i`ʜVV>Ȝ˜>Ю°К
The time between descaling operations depends on the quality of the water and the
frequency with which you use the appliance. The appliance must be descaled at least once
a year or after 50 hours of use.
UÊ/œÊV>ААЮКœХМК>Ê`iÃV>ˆ˜}ʜ«iÀ>̈œ˜]КvœœЬКМ iКvœœЬˆ˜}ÊÃÌi«Ã\
1. Ensure that the appliance has cooled down completely (2 hours minimum).
2. Fill the water tank with fresh untreated tap water and place it on the main unit
allowing water to fill the boiler.
3. Remove the water tank from the base and empty out the water via the water tank
filling hole by tipping the appliance over a sink. Limescale and other impurities can
be rinsed away.
4. Repeat step 2 and 3 several times until all the scale has been removed.
CAUTION: Don’t fill the boiler by the steam head holes!
Never immerse the steam head in water!