Yamaha AW1600 - Manual (Page 204)

AW1600 Owner’s Manual
Troubleshooting
204
Appendix
■ Editing results are not heard in the sound
• Have you selected the virtual track that you recorded?
• Are you using the appropriate editing command?
■ Counter display is not 0 when you return to
the beginning of the song
• The display mode may be set to REMAIN (remaining
recording time).
• If the display mode is set to REL (relative time), the start
point may be specified.
→ Go to the SONG screen SETUP, POINT page and check the
settings.
■ Display indicates DISK FULL, MEMORY
FULL, or REGION FULL, and you cannot
record or edit
• There is insufficient free space, or too many recording
regions. Erase unneeded tracks and then perform the Opti-
mize operation to obtain more free space.
• If the “DISK FULL” message appears, erase unneeded
songs, sample libraries, or WAV files located under the
“Transport” folder. The WAV files under the “Transport”
folder can be erased from your computer when the USB
Storage mode is engaged.
■ The display indicates DISK BUSY during
playback
• The recorded data might be so fragmented that the read
speed is significantly reduced. It might be necessary to
backup all hard disk data to your computer and then re-ini-
tialize the hard disk.
■ When you press a pad there is no sound, or
the wrong bank is heard
• Have you selected a bank to which the waveform is
assigned?
• A bank change may have been specified in the SONG
screen TEMPO page.
■ The sound is not what you loaded, or the
sound is different depending on whether
you are stopped or playing
• If the playback mode is set to LOOP, the sound will play
according to the monitor tempo specified in the SAMPLE
screen SETUP page while the recorder is stopped, and
will play according to the song tempo while the recorder is
playing.
■ The sound you loaded only plays part of the
way
• Have you made trim settings to shorten the Start–End
region?
• If the playback mode is set to GATE, the sample will play
only while you continue pressing the pad.
• If the playback mode is set to LOOP and Slice is turned
off, the sample will play only for the length of a measure.
■ The display indicates MEMORY FULL, and
you can’t import
• Access the SAMPLE screen MEMORY page, and check
the amount of used memory. Execute ERASE or
EXTRACT to increase the amount of free memory.
■ WAV files to be imported are not displayed
• Have you copied WAV files with a different bit depth from
the song? 16-bit WAV files will not be displayed for a 24-
bit song, and 24-bit WAV files will not be displayed for a
16-bit song. WAV files with sampling frequency other than
44.1 kHz will also not be displayed.
■ Can’t exchange MIDI data
• Are the MIDI cables or USB cables connected correctly?
• A MIDI cable or USB cable may be broken.
• Is the power turned on for the transmitting and receiving
devices?
• Do the channel settings match for the transmitted and
receiving devices?
• Have the appropriate settings been made in the UTILITY
screen MIDI 1/2 pages?
→ Select the connector and port to be used (MIDI connector,
USB connector port 1/2) in the MIDI 1 page.
• Is a scene assigned to the program change number being
transmitted?
• If a USB connection is being used, is the required USB-
MIDI driver properly installed on your computer?
■ MTC messages are not transmitted
• In the UTILITY screen MIDI 2 page, has the MTC button
been turned on?
• Is MTC SYNC set to MASTER?
■ The AW1600 does not synchronize to
incoming MTC messages
• Is the MIDI cable connected to the MIDI IN connector?
• In the UTILITY screen MIDI 2 page, has MTC MODE
been set to SLAVE?
• Is the connector and port to be used (MIDI connector,
USB connector port 1/2) selected in the UTILITY screen
MIDI 1 page?
■ MTC synchronization drifts
• Is a large amount of MIDI data (notes etc.) being received
together with the MTC messages?
• Does the frame rate match between the AW1600 and the
external device?
• In the UTILITY screen MIDI 2 page, the OFST (offset)
may have been set.
• If jumps occur in the synchronized time, change the
AVRG setting in the UTILITY screen MIDI 2 page, and
try again.
■ MMC messages is not transmitted
• Is the MIDI cable connected to the MIDI OUT connector?
• In the UTILITY screen MIDI 1 page, has MMC MODE
been set to MASTER? Does the DEVICE NO. match?
Sampler operations
MIDI operations